Prodotto finitoview
The Viper 474V is a 4-button remote control designed for use with compatible Viper vehicle security and remote start systems. This remote allows for convenient control of your vehicle's security features, including locking, unlocking, auxiliary functions, and remote start/panic.
Image: Viper 474V 4-Button Remote. This image displays the front of the remote control, featuring four distinct buttons: a lock icon, an unlock icon, an 'AUX' button, and an orange button with a speaker/horn icon. The Viper logo is visible below the buttons, and a metal key ring is attached at the bottom.
Installazione e programmazione
To program your Viper 474V remote to your vehicle's security system, follow these steps. Ensure you have located your system's valet switch, typically found under the driver's lower dash or on the driver's side kick panel. The exact procedure may vary slightly depending on whether your Viper system includes a remote start module.
- Preparare il veicolo: Open the driver's side door.
- Accensione inserita: Insert the key into the ignition and turn it to the "Run" position. Do not start the engine. All dashboard warning lights should illuminate.
- Accedere alla modalità di programmazione:
- With Remote Start Module: Press and release the valet button once. This selects Channel 1.
- Without Remote Start Module: Press and release the valet button seven (7) times. This selects Channel 7.
- Confirm Channel Selection: Press the valet button once more and hold it down. The alarm LED on the dash will flash the same number of times as the selected channel (1 or 7), and the siren (if connected) will chirp to confirm. Continue holding the valet button.
- Programmare il telecomando: While still holding the valet button, press the "Lock" button on your new Viper 474V remote. Hold the "Lock" button until the siren sounds, indicating successful programming.
- Uscire dalla modalità di programmazione: Release the "Lock" button on the remote, then release the valet button. Turn the ignition key to the "Off" position and remove it from the vehicle. Close the driver's door.
- Prova il telecomando: Test the new remote by attempting to lock and unlock the vehicle.
Note: If you wish to erase all previously programmed remotes and program only the new one, consult your system's specific installation manual for the master reset procedure, which typically involves a different valet button sequence.
Istruzioni per l'uso
The Viper 474V remote features four buttons for controlling your vehicle's security system:
- Pulsante di blocco (🔒): Premere per attivare il sistema di sicurezza e bloccare le portiere del veicolo.
- Pulsante di sblocco (🔓): Premere per disattivare il sistema di sicurezza e sbloccare le portiere del veicolo.
- Pulsante AUX: This button controls an auxiliary function, which can be programmed for various purposes such as trunk release, power windows, or other accessories. Refer to your system's installation manual for the specific function assigned to this button.
- Orange Button (Speaker/Horn Icon): This button typically activates the remote start function (if installed and programmed) or the panic alarm.
- Avvio remoto: Press twice to activate remote engine start.
- Panico: Press and hold for a few seconds to activate the panic alarm. Press again to deactivate.
Note: Button sensitivity is high. Be mindful when carrying the remote in pockets to avoid unintentional activation of functions like remote start or panic.
Manutenzione
Sostituzione della batteria
The Viper 474V remote is powered by a small battery. If the remote's range decreases significantly or it stops responding, the battery may need replacement. To replace the battery:
- Aprire con cautela il telecomando casing. This usually involves prying it open along the seam with a small, flat tool.
- Note the type and orientation of the existing battery.
- Remove the old battery and insert a new one of the same type, ensuring correct polarity.
- Chiudere il telecomando casing in modo sicuro.
Smaltire sempre le batterie usate in modo responsabile, nel rispetto delle normative locali.
Risoluzione dei problemi
- Il telecomando non risponde:
- Controllare la batteria. Sostituirla se necessario.
- Ensure the remote is within range of the vehicle's receiver.
- Re-attempt the programming steps outlined in the "Setup and Programming" section.
- Verify that the valet switch is functioning correctly.
- Unintentional Activations:
- The buttons on the 474V remote are sensitive. Avoid placing the remote in tight pockets or areas where buttons might be accidentally pressed.
- Gamma limitata:
- Sostituire la batteria del telecomando.
- Ensure there are no large metallic objects or electronic devices interfering with the signal between the remote and the vehicle.
Specifiche
- Numero modello: 474V
- Marca: VIPERA
- Dimensioni del prodotto: 8 x 6 x 1.75 pollici
- Peso dell'articolo: 2.4 once
- Tecnologia di connettività: Infrarossi
- Caratteristica speciale: Design ergonomico
- Dispositivi compatibili: Vehicle Alarm Systems
- Numero massimo di dispositivi supportati: 1
Garanzia e supporto
For warranty information, technical support, or further assistance with your Viper 474V remote or associated vehicle security system, please refer to the documentation provided with your complete Viper system or contact Directed Electronics Inc., the manufacturer, directly. You can typically find support contact details on the manufacturer's official websito.
It is recommended to register your product with the manufacturer, if applicable, to ensure you receive updates and support.