Clover B14A Hot and Cold Bottled Water Dispenser User Manual

1. Introduzione

The Clover B14A Hot and Cold Bottled Water Dispenser provides convenient access to refreshing chilled drinking water and piping hot water. Designed for home or office use, this dispenser features hygienic stainless steel tanks and an efficient cooling and heating system. Please read this manual thoroughly before operation to ensure safe and optimal performance.

2. Informazioni sulla sicurezza

• Sicurezza elettrica: This appliance operates on 110-120 volts, 50-60 Hz. Ensure the power outlet is properly grounded. Do not use with damaged cords or plugs.
• Sicurezza dell'acqua calda: The hot water temperature reaches approximately 185°F (85°C). Exercise extreme caution when dispensing hot water to prevent burns. A safety switch is provided for the hot water dispenser.
• Sicurezza dei bambini: Always engage the hot water safety switch when children are present to prevent accidental dispensing of hot water.
• Posizionamento: Place the dispenser on a flat, stable surface away from direct sunlight, heat sources, and areas with high humidity. Ensure adequate ventilation around the unit.
• Bottiglia d'acqua: Use only standard 5-gallon (18.9-liter) water bottles.
• Manutenzione: Scollegare l'unità prima di pulirla o di effettuare qualsiasi intervento di manutenzione.

3. Impostazione

1. Disimballaggio: Estrarre con cautela il dispenser dalla confezione. Verificare che non vi siano danni.
2. Posizionamento: Position the dispenser on a level, sturdy surface. Allow at least 4 inches (10 cm) of clearance from walls for proper ventilation.
3. Installare il vassoio raccogligocce: Insert the concealed, lift-out drip tray into its designated slot below the spigots.
4. Pulizia iniziale: Before first use, clean the exterior with a soft, damp stoffa.
5. Installa la bottiglia d'acqua: Remove the protective seal from a new 5-gallon water bottle. Lift the bottle and quickly invert it, placing it firmly onto the bottle support on top of the dispenser. Ensure the bottle is seated correctly to prevent leaks.
6. Sistema di scarico: Before plugging in, dispense at least 1 liter (approximately 4 cups) of water from both the hot and cold spigots to ensure the tanks are filled and to flush any air from the system.
7. Collegare: Collegare il cavo di alimentazione a una presa elettrica da 110-120 V dotata di messa a terra.

Figura 1: Completo view of the Clover B14A water dispenser with a 5-gallon bottle.

4. Istruzioni per l'uso

1. Accensione: Once plugged in, the dispenser will begin cooling and heating the water. Allow approximately 15-30 minutes for the water to reach desired temperatures.
2. Erogazione acqua fredda: Place your cup under the cold water spigot (typically blue). Push the lever to dispense cold water. Release the lever to stop.
3. Erogazione Acqua Calda: Place your cup under the hot water spigot (typically red). To dispense hot water, first push the safety switch (often a red button or lever) and then push the main lever. Release both to stop.
4. Interruttore dell'acqua calda: The hot water function can be turned on or off using the switch located on the back of the unit. Turning it off will prevent the water from heating, saving energy and acting as an additional safety measure.
5. Adjusting Cold Water Temperature: The cold water temperature can be adjusted via a thermostat control, usually located on the back of the unit. It allows for a range of 35.6°F to 53.6°F (2°C to 12°C).

Figure 2: Detail of the hot (red) and cold (blue) water spigots with the hot water safety switch.

5. Manutenzione

• Pulizia del vassoio raccogli gocce: The drip tray is removable for easy cleaning. Periodically empty and wash the tray with mild soap and water.
• Pulizia esterna: Pulire le superfici esterne con un panno morbido, damp panno. Non usare detergenti abrasivi o solventi.
• Decalcificazione: Over time, mineral deposits may accumulate in the hot water tank. Consult the manufacturer's website or customer support for recommended descaling procedures.
• Pulizia del serbatoio dell'acqua: For thorough cleaning of the internal water tanks, it is recommended to contact a qualified service technician.

6. Risoluzione Dei Problemi

• Nessuna erogazione di acqua: Ensure the water bottle is properly seated and not empty. Check if the unit is plugged in and powered on.
• Niente acqua calda: Verify the hot water switch on the back of the unit is in the 'ON' position. Check if the thermal reset button (often a small red button on the back) needs to be pressed.
• Niente acqua fredda: Ensure the unit is plugged in and the cold water thermostat is set to a desired temperature.
• Perdita: Controllare che la borraccia non presenti crepe o non sia posizionata correttamente. Assicurarsi che il vassoio raccogligocce sia installato correttamente.
• Rumore insolito: The unit is designed for quiet operation. If unusual or excessive noise occurs, ensure the unit is on a level surface and not vibrating against a wall. If noise persists, contact customer support.

7. Specifiche

• Modello: B14A
• Dimensioni (P x L x A): 12.3" x 12.7" x 37.9" (31.2 cm x 32.3 cm x 96.3 cm)
• Peso: 32 libbre (14.5 kg)
• Colore: Black with Steel side panels
• Voltage: 110-120 V
• Frequenza: Frequenza
• Temperatura dell'acqua calda: Approximately 185°F (85°C) (non-adjustable)
• Temperatura dell'acqua fredda: 35.6°F - 53.6°F (2°C - 12°C) (adjustable)
• Compatible Bottle Sizes: 5 galloni (18.9 litri)
• Materiali da costruzione: Acciaio inossidabile, plastica
• Certificazioni: CE, NSF, UL, Energy Star Rated
• vassoio antigoccia: Concealed, lift-out design, high impact, durable ABS. Removable, anti-splash grid.

8. Garanzia e supporto

The Clover B14A Hot and Cold Bottled Water Dispenser comes with a Garanzia limitata del produttore di 1 anno. For warranty claims, technical assistance, or further inquiries, please contact Clover customer support. Keep your purchase receipt as proof of purchase.