Introduzione
This manual provides essential information for the safe and effective use of the Hakko CHP TR-20-TM Micro Soft Wire Cutter. This precision tool is designed for cutting integrated circuit (IC) pins and soft wires up to 22 AWG (0.6mm).
Figure 1: Hakko CHP TR-20-TM Micro Soft Wire Cutter. This image displays the tool's overall design, highlighting its red and black ergonomic handles and the precise, angled cutting jaws.
Caratteristiche del prodotto
- Reverse-Cut Micro Soft-Wire Cutter: Features an 8mm long jaw with a reverse angle head, specifically designed for flush-cutting IC pins up to 22 gauge (0.6mm).
- Angled Cutting Surface: The 48-degree reverse angled cutting surface facilitates precise cutting of closely-spaced IC pins.
- Costruzione durevole: Constructed from 2.0mm heat-treated carbon steel for enhanced durability and extended tool life.
- Funzionamento regolare: Precision-ground holes and surfaces ensure smooth movement of the cutting jaws.
- Reduced Operator Fatigue: An internal spring mechanism automatically returns the tool to the open position after each cut, minimizing hand strain.
- Design ergonomico: Dolphin-style nonslip hand grips provide comfort and control during prolonged use.
- Protezione della mano: A curved fore-edge on the handles protects hands from cutting surfaces.
- Resistenza alla corrosione: Parkerized surfaces prevent glare and increase the tool's resistance to corrosion.
Impostare
The Hakko CHP TR-20-TM Micro Soft Wire Cutter is ready for use out of the packaging. No assembly is required.
- Ispezione iniziale: Before first use, inspect the tool for any signs of damage or manufacturing defects. Ensure the jaws align properly and the spring mechanism operates smoothly.
- Pulizia: Ensure the cutting jaws are clean and free of debris before use to maintain optimal cutting performance.
Istruzioni per l'uso
Follow these instructions for safe and effective operation of the wire cutter.
- La sicurezza prima di tutto: Always wear appropriate eye protection when using cutting tools to prevent injury from flying debris.
- Presa: Hold the cutter firmly with the ergonomic handles. The nonslip grips are designed for comfort and control.
- Posizionamento: Position the wire or IC pin to be cut between the jaws. For flush cuts on IC pins, align the reverse-angled jaw as close as possible to the circuit board or component body.
- Capacità di taglio: Do not attempt to cut wires or materials exceeding the maximum capacity of 22 AWG (0.6mm) for soft wire. Cutting harder or thicker materials can damage the tool's jaws.
- Azione di taglio: Apply steady, firm pressure to the handles to close the jaws and make the cut. The internal spring will reopen the jaws automatically upon release.
- Disposizione: Dispose of cut wire pieces responsibly.
Manutenzione
Proper maintenance ensures the longevity and performance of your Hakko wire cutter.
- Pulizia: After each use, wipe the jaws and handles with a clean, dry cloth to remove any debris or residue. For stubborn grime, a slightly damp è possibile utilizzare un panno e procedere con un'asciugatura accurata.
- Lubrificazione: Periodically apply a small drop of light machine oil to the pivot point to ensure smooth operation and prevent rust. Wipe off any excess oil.
- Magazzinaggio: Store the tool in a dry environment to prevent corrosion. Keep the jaws closed when not in use to protect the cutting edges.
- Evitare di far cadere: Dropping the tool, especially on hard surfaces, can misalign or damage the precision jaws.
Risoluzione dei problemi
This section addresses common issues you might encounter with your wire cutter.
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Jaws do not close completely or align properly. | Debris caught between jaws or pivot point; tool has been dropped or damaged. | Clean jaws thoroughly. If damage is suspected, discontinue use and consider replacement. |
| Cutting performance is poor or requires excessive force. | Dull or damaged cutting edges; attempting to cut material beyond capacity. | Inspect cutting edges for nicks or wear. Ensure material is within 22 AWG (0.6mm) soft wire limit. Replace if edges are significantly damaged. |
| Handles feel stiff or sticky. | Lack of lubrication at the pivot point; accumulation of dirt. | Clean the pivot area and apply a small amount of light machine oil. |
Specifiche
| Attributo | Dettaglio |
|---|---|
| Numero di modello | TR-20-TM |
| Tipo di mascella | Reverse-cut, Micro Flush-cut |
| Jaw Length | 8mm |
| Angolo della mascella | 48-degree reverse angle |
| Massima capacità di taglio | 22 AWG (0.6mm) soft wire / IC pins |
| Materiale da costruzione | 2.0mm Heat-treated Carbon Steel |
| Materiale della maniglia | Alloy Steel with Nonslip Grips |
| Colore | Rosso |
| Peso dell'articolo | 0.1 libbre (circa 45 grammi) |
| Produttore | Quality Hand Tools |
Garanzia e supporto
For warranty information or technical support regarding your Hakko CHP TR-20-TM Micro Soft Wire Cutter, please contact American Hakko Products directly. American Hakko Products manufactures soldering and desoldering tools and is headquartered in Valencia, CA.
Please refer to the official Hakko websito o la documentazione di acquisto per i termini di garanzia e i dettagli di contatto più aggiornati.
Produttore: Quality Hand Tools (as listed on product specifications, associated with Hakko brand)
Marca: Hakko
Websito: www.hakko.com