Sostituzione della luce di cortesia Lamp Manuale d'uso del modulo

Informazioni importanti sulla sicurezza

La lampadina in questa lamp contains Mercury (Hg). Please dispose of in accordance with local, state, or federal laws. Do not dispose of with regular household waste.

• Always disconnect the projector from the power outlet before attempting any installation or maintenance.
• Allow the projector to cool down completely (at least 30 minutes) before replacing the lamp. Caldo lamppossono causare gravi ustioni.
• Avoid touching the glass surface of the new lamp directly with bare hands. Oils from your skin can reduce lamp life. Use gloves or a clean cloth if necessary.
• Non forzare il lamp module into place. If it does not fit easily, recheck the orientation and ensure it is the correct lamp for your projector model.
• Never operate the projector with the lamp coperchio rimosso.
• Mantieni la lamp module out of reach of children.

Istruzioni per l'installazione

1. Spegnimento e disconnessione: Ensure your Boxlight projector is turned off and completely unplugged from the power source.
2. Raffreddare: Allow the projector to cool down for at least 30 minutes. The lamp operates at high temperatures and can cause burns if handled while hot.
3. Localizza Lamp Copertina: Refer to your projector's user manual to locate the lamp compartment cover. This is typically secured by one or more screws.
4. Rimuovi lamp Copertina: Using a suitable screwdriver, carefully remove the screw(s) securing the lamp cover and then remove the cover.
5. Unscrew Old Lamp: Il vecchio lamp module will be secured by one or more screws. Unscrew these fasteners.
6. Rimuovi la vecchia Lamp: Gently pull the handle on the old lamp module to slide it out of the projector. Be careful not to drop it.
7. Inserisci nuova Lamp: Carefully insert the new Boxlight replacement lamp module into the projector, ensuring it slides smoothly into place. Do not force it.
8. Nuovo L sicuroamp: Fasten the new lamp module with the screw(s) you removed earlier. Ensure it is securely seated.
9. Sostituisci Lamp Copertina: Riattacca il lamp compartment cover and secure it with its screw(s).
10. Ricollegare l'alimentazione: Plug the projector back into the power outlet.
11. Reimposta Lamp Timer: Consult your projector's user manual for instructions on how to reset the lamp timer. This is crucial for accurate lamp life tracking.

Linee guida operative

• Spegnimento corretto: Always allow the projector to complete its cooling cycle after use before unplugging it. Abrupt power cuts can shorten lamp vita.
• Ventilazione: Ensure the projector has adequate ventilation. Blocked vents can lead to overheating and reduced lamp vita.
• Evitare cicli frequenti di accensione/spegnimento: Turning the projector on and off frequently can stress the lamp and reduce its lifespan.
• Eco Mode (if available): If your projector has an "Eco Mode" or similar power-saving setting, using it can extend lamp vita.

Manutenzione

• Pulizia del filtro dell'aria: Regularly clean or replace your projector's air filter as per your projector's manual. A clogged filter can cause the projector to overheat, negatively impacting lamp vita.
• Rimozione della polvere: Keep the projector free from dust. Use a soft, dry cloth to wipe the exterior. Do not use abrasive cleaners or solvents.
• Lamp Gestione: Quando si maneggia la lamp module, always hold it by its housing, not the bulb itself.

Risoluzione dei problemi

Se riscontri problemi dopo l'installazione del nuovo lamp, considera quanto segue:

• Lamp Non si accende:
  • Assicurare lamp il modulo è completamente inserito e fissato con le sue viti.
  • Verificare la lamp cover is correctly installed and secured. Many projectors have a safety switch that prevents operation if the cover is open.
  • Check that the projector is properly plugged into a working power outlet.
• Dim Image or Poor Color:
  • Conferma la lamp timer has been reset. If not, the projector might still be operating under the assumption of an old, worn-out lamp.
  • Check projector settings for brightness or picture modes.
  • Assicurarsi che la lente del proiettore sia pulita.
• "Lamp Error" Message:
  • This often indicates the lamp is not properly installed or the lamp cover is not secured. Re-check installation steps.
  • If the error persists, the lamp itself might be faulty. Contact customer support.

For further assistance, refer to your projector's original user manual or contact Boxlight customer support.

Specifiche del prodotto

Informazioni sulla garanzia

This Boxlight replacement lamp module is covered by a 180-Giorno di garanzia dalla data di acquisto. La presente garanzia copre i difetti di materiali e fabbricazione in condizioni di normale utilizzo. Si prega di conservare la prova d'acquisto per eventuali reclami in garanzia.

For warranty service or inquiries, please contact the seller or manufacturer directly.

Assistenza clienti

If you require further assistance, have questions about installation, or need to report an issue, please contact the retailer where you purchased this product or the manufacturer, Arclyte Tech. (Boxlight's manufacturer).

When contacting support, please have your product model number (ACTG042) and proof of purchase readily available.