Intotal Direct Hard Wire Cord Instruction Manual

Introduzione

This manual provides comprehensive instructions for the proper installation and use of your Intotal Direct Hard Wire Cord. This product is designed to provide a permanent and clean power connection for compatible Uniden Radar Detectors, eliminating the need for a cigarette lighter adapter. Please read this manual thoroughly before installation to ensure correct setup and safe operation.

Informazioni sulla sicurezza

• Installazione professionale consigliata: If you are not familiar with automotive electrical systems, it is highly recommended to seek professional installation to prevent damage to your vehicle or the product.
• Scollegare l'alimentazione: Prima di effettuare qualsiasi intervento elettrico, scollegare sempre la batteria del veicolo per evitare cortocircuiti o scosse elettriche.
• Messa a terra corretta: Ensure the black ground wire is securely connected to a clean, unpainted metal surface on the vehicle chassis.
• Protezione del fusibile: The red positive wire includes an inline fuse for circuit protection. Do not bypass or replace this fuse with one of a higher ampvalutazione di età.
• Instradamento dei cavi: Route cables carefully to avoid interference with vehicle controls, pedals, airbags, or other safety features. Secure cables to prevent snagging or damage.
• Voltage Compatibilità: This cord is designed for 12V DC automotive systems. Do not use with other voltage fonti.

Contenuto della confezione

• 1 x Intotal Direct Hard Wire Cord with RJ11 Connector

Guida all'installazione

This hard wire cord provides a direct power connection to your vehicle's electrical system, allowing your Uniden radar detector to power on and off with the vehicle's ignition. A fuse tap (not included) is typically required for a safe and proper connection to the fuse box.

Installazione passo dopo passo

1. Identificare la fonte di alimentazione: Locate your vehicle's fuse box, typically found under the dashboard, in the engine bay, or in the trunk. Consult your vehicle's owner's manual for its exact location.
2. Locate a Switched Fuse: Using a circuit tester, identify a fuse that provides power only when the vehicle's ignition is on (a 'switched' power source). Avoid fuses critical to vehicle safety systems.
3. Connect Positive Wire: Using a fuse tap (sold separately), connect the red positive wire of the hard wire cord to the identified switched fuse slot. Ensure the fuse tap is installed correctly with the appropriate fuse for the radar detector.
4. Collegare il filo di terra: Locate a clean, unpainted metal bolt or screw on the vehicle's chassis. Securely attach the black ground wire's ring terminal to this point. A good ground connection is crucial for proper operation.
5. Route RJ11 Cable: Carefully route the RJ11 cable from the power connection point to the desired mounting location of your Uniden radar detector. Ensure the cable is hidden and secured to prevent interference with driving or vehicle components.
6. Connect to Radar Detector: Plug the RJ11 connector firmly into the RJ11 power jack on your Uniden radar detector.
7. Prova di connessione: Turn on your vehicle's ignition. The radar detector should power on automatically. Turn off the ignition; the detector should power off.

This image displays the Intotal Direct Hard Wire Cord. It features a black cable with a clear RJ11 connector on one end, designed to plug into compatible Uniden radar detectors. The other end splits into two wires: a red wire with a spade connector for positive power connection, and a black wire with a ring terminal for grounding to the vehicle chassis. An inline fuse holder is visible on the red wire for circuit protection. The cable is marked with specifications such as 24AWG, 80°C, and 300V.

Operazione

Once properly installed, the Intotal Direct Hard Wire Cord will provide power to your compatible Uniden radar detector whenever your vehicle's ignition is turned on. The detector will power off automatically when the ignition is switched off. Please note that using a direct hard wire cord typically bypasses the mute button or other features found on standard cigarette lighter power adapters.

Manutenzione

• Ispezione regolare: Controllare periodicamente il cavo per verificare la presenza di segni di usura, sfilacciamento o danneggiamento.
• Integrità della connessione: Ensure all connections (RJ11, positive, and ground) remain secure and free from corrosion.
• Controllo fusibile: If the radar detector stops receiving power, inspect the inline fuse on the red wire and the fuse in the fuse tap (if used) for continuity. Replace only with a fuse of the same ampvalutazione di età.

Risoluzione dei problemi

Specifiche del prodotto

• Marca: Totale
• Nome modello: Direct Hard Wire Cord
• Numero modello: 4336324677
• Tipo di connettore: RJ11
• Tipo di cavo: Cablaggio
• Dispositivi compatibili: Uniden LRD850, LRD950, DFR6, DFR7, DFR8, DFR9, R1, R3, R7 Radar Detectors
• Caratteristica speciale: Direct and permanent installation
• Volume massimotage: 16 Volt (CC)
• Peso dell'articolo: Circa 2.39 once
• Dimensioni del prodotto: 6 x 1 x 4 pollici (confezione)

Garanzia e supporto

For any questions, technical assistance, or warranty inquiries regarding your Intotal Direct Hard Wire Cord, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase for warranty claims.