HUBBELL 7051-G Receptacle Instruction Manual

Introduzione

This manual provides essential instructions for the safe installation, operation, and maintenance of the Hubbell 7051-G 15A, 125V-AC, 2-Pole, 3-Wire Receptacle. Please read this manual thoroughly before installation and retain it for future reference. Proper installation by a qualified electrician is recommended.

Informazioni sulla sicurezza

AVVERTIMENTO: Risk of electric shock or fire. Improper installation can result in serious injury or death. Always turn off power at the circuit breaker or fuse box before installing or servicing this device. Use only copper wire with this device. Do not use with aluminum wire unless specifically rated for it. Ensure all connections are tight and secure.

• Scollegare sempre l'alimentazione prima di lavorare sui circuiti elettrici.
• Se non si è sicuri di una qualsiasi fase del processo di installazione, consultare un elettricista qualificato.
• Rispettare tutte le normative elettriche locali e nazionali.
• Non superare i valori elettrici nominali specificati per il dispositivo.

Prodotto finitoview

The Hubbell 7051-G is a 15 Amp, 125 Volt, 2-pole, 3-wire grounding duplex receptacle designed for general-purpose electrical applications. It features a durable nylon construction and is suitable for various residential and commercial installations.

Immagine: Frontale view of the Hubbell 7051-G duplex receptacle, showing two outlets with grounding slots.

Configurazione e installazione

Strumenti necessari: Screwdriver (Phillips and/or flathead), Wire Strippers, VoltageTester.

1. Spegnimento dell'alimentazione: Locate the circuit breaker or fuse that controls the outlet you are working on and turn it off. Verify power is off using a voltagetester.
2. Rimuovere la vecchia presa (se applicabile): Unscrew the wall plate and then the mounting screws holding the old receptacle in the electrical box. Carefully pull the receptacle out and disconnect the wires.
3. Preparare i cavi: Strip approximately 1/2 inch of insulation from the ends of the circuit wires. Ensure the wire ends are clean and straight.


Immagine: Lato view of the Hubbell 7051-G receptacle, showing the strip gauge for proper wire preparation.

4. Collegare i fili:
   • Green or Bare Copper Wire (Ground): Collegare alla vite di messa a terra verde.
   • White Wire (Neutral): Connect to the silver screw.
   • Black or Red Wire (Hot/Live): Connect to the brass screw.
   Ensure wires are securely wrapped around the screws in a clockwise direction and tightened firmly.


Immagine: Indietro view of the Hubbell 7051-G receptacle, illustrating the screw terminals for wiring connections (brass for hot, silver for neutral, green for ground).



Image: Close-up of the rear of the Hubbell 7051-G receptacle, detailing the wire strip gauge and voltage ratings (15A, 125V and 10A, 250V).

5. Presa di montaggio: Carefully push the wired receptacle back into the electrical box. Secure it with the provided mounting screws.
6. Installa la piastra a muro: Fissare la piastra decorativa a muro sopra la presa.
7. Ripristina alimentazione: Turn the power back on at the circuit breaker or fuse box. Test the receptacle with a known working device.

Istruzioni per l'uso

To operate the Hubbell 7051-G receptacle, simply insert the plug of your electrical device into one of the two available outlets. Ensure the plug is fully inserted. The receptacle is designed for standard 2-prong or 3-prong grounded plugs.

Immagine: Frontale view of the Hubbell 7051-G receptacle, ready for device plugs.

Manutenzione

The Hubbell 7051-G receptacle requires minimal maintenance. Periodically inspect the receptacle and wall plate for any signs of damage, cracks, or discoloration. If any damage is observed, turn off power at the circuit breaker and replace the receptacle immediately. Clean the surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.

Risoluzione dei problemi

• No Power at Receptacle:
  • Check the circuit breaker or fuse for the circuit. Reset the breaker or replace the fuse if tripped/blown.
  • Ensure all wire connections are secure. Turn off power before checking connections.
  • Testare la presa con un voltage tester to confirm power presence.
• Collegamento della spina allentato:
  • If plugs do not stay firmly in the receptacle, the internal contacts may be worn. The receptacle should be replaced by a qualified electrician.
• Surriscaldamento:
  • If the receptacle feels warm to the touch, immediately disconnect all devices and turn off power. This could indicate an overload or a faulty connection. Consult a qualified electrician.

Specifiche

Image: The Hubbell 7051-G receptacle shown in its original product box.

Image: Barcode label for the Hubbell 7051-G 2P 3W 15A 125V-AC Receptacle, showing product identification details including UPC 0129190665219.

Garanzia e supporto

Specific warranty information for the Hubbell 7051-G Receptacle is not provided within this manual. For warranty details or technical support, please contact Hubbell customer service directly or visit their official websito. Conserva la ricevuta d'acquisto come prova d'acquisto.

Produttore: HUBBELL

Websito: www.hubbell.com (Exampil collegamento (il collegamento effettivo può variare)