SOMMER Pearl 4018 Garage Door Remote Control User Manual

1. Introduzione

This manual provides instructions for the safe and efficient operation, setup, and maintenance of your SOMMER Pearl 4018 4018V000 TX55-868-4 garage door remote control. This device utilizes the SOMloq2 radio system and is compatible with Somloq Rollingcode systems, as well as Pro Teckentrup Drive models 4020, 4026, and 4031 Slider.

Figura 1: SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control. This image shows the compact, modern design of the remote control, featuring four buttons and a stainless steel application.

2. Informazioni sulla sicurezza

• Keep the remote control out of reach of children to prevent accidental operation of the garage door.
• Non permettere ai bambini di giocare con il telecomando o con l'apriporta del garage.
• Prima di azionare la porta del garage, assicurarsi che sia visibile e libera da ostacoli.
• Do not operate the garage door if people or objects are in its path.
• Smaltire le batterie secondo le normative locali. Non incenerire le batterie.
• Evitare di esporre il telecomando a temperature estreme, umidità o luce solare diretta.

3. Contenuto della confezione

Verifica che tutti gli articoli siano presenti nel tuo pacco:

• SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control (quantity as purchased, typically 2 units)
• 3V CR2032 Lithium-metal battery (pre-installed or included)

4. Configurazione e programmazione

The SOMMER Pearl 4018 remote control must be programmed to your garage door opener receiver. The exact programming steps may vary slightly depending on your specific SOMMER garage door opener model. Refer to your garage door opener's manual for precise instructions. A common programming method is outlined below:

1. Individuare il ricevitore: Identify the garage door opener's motor unit. On the motor unit, locate the "Learn" or "Program" button. This button is often small and may be recessed.
2. Attiva la modalità di apprendimento: Press and immediately release the "Learn" or "Program" button on your garage door opener. The indicator light on the opener will typically illuminate or flash, indicating it is in learn mode. You usually have about 30 seconds to complete the next step.
3. Programmare il telecomando: Within the learn mode timeframe, press and hold the desired button on your SOMMER Pearl 4018 remote control that you wish to use for operating the garage door.
4. Conferma programmazione: Release the button on the remote control once the garage door opener's indicator light flashes or changes color, or if the garage door moves slightly. This indicates successful programming.
5. Operazione di prova: Press the programmed button on your remote control to ensure it operates the garage door correctly.
6. Programmazione di telecomandi aggiuntivi: Repeat these steps for any additional SOMMER Pearl 4018 remote controls you wish to program.

Note: If your garage door opener has a different programming procedure (e.g., using a master remote or a specific sequence), please consult your opener's manual.

5. Istruzioni per l'uso

Once programmed, operating your SOMMER Pearl 4018 remote control is straightforward:

• Apertura/Chiusura della Porta: Press the programmed button on your remote control once. The garage door will begin to open or close.
• Fermare la porta: Press the same programmed button again while the door is in motion to stop it.
• Porte multiple: If you have programmed multiple garage doors to different buttons on your remote, press the corresponding button for the desired door.
• Allineare: The remote control has an approximate range of 50-140 meters, depending on environmental conditions and obstructions.

6. Manutenzione

6.1. Sostituzione della batteria

The SOMMER Pearl 4018 remote control uses a 3V CR2032 Lithium-metal battery. When the remote's range decreases significantly or it stops responding, it is likely time to replace the battery.

1. Apri il Casing: Aprire con cautela il telecomando casing. This usually involves prying it open with a small flat-head screwdriver or a similar tool at a designated notch.
2. Rimuovere la vecchia batteria: Note the orientation of the old CR2032 battery (positive (+) side up or down). Gently remove the old battery.
3. Inserire una nuova batteria: Insert a new 3V CR2032 Lithium-metal battery, ensuring the correct polarity. The positive (+) side typically faces upwards.
4. Chiudi Casing: Aggancia il telecomando casing rimetterli insieme in modo sicuro.
5. Test: Test the remote control to ensure it functions correctly with the new battery.

6.2. Pulizia

Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or allow moisture to enter the casing.

7. Risoluzione Dei Problemi

8. Specifiche

• Modello: Pearl 4018 4018V000 TX55-868-4
• Sistema radiofonico: SOMloq2
• Pulsanti: 4
• Frequenza radio: FM 868.8 MHz, FM 868.95 MHz
• Allineare: Circa 50-140 metri (a seconda dell'ambiente)
• Dimensioni: 79 x 26 x 13 mm (3.11 x 1.02 x 0.51 pollici)
• Tipo di batteria: 3V CR2032 Lithium-metal
• Peso: 40 g (1.41 once)
• Compatibilità: Somloq Rollingcode system, Pro Teckentrup Drive (compatible with 4020, 4026, 4031 Slider)

9. Garanzia e supporto

For warranty information and technical support, please refer to the documentation provided with your original purchase or contact SOMMER customer service directly. Contact details can typically be found on the manufacturer's official websito.