LICHIFIT 4100E 2.4G 4-Channel Micro Receiver Instruction Manual

1. Prodotto finitoview

The LICHIFIT 4100E is a compact 2.4GHz 4-channel micro receiver designed for use with JR and SPEKTRUM DSM2 compatible transmitters. This receiver is suitable for various remote-controlled models, offering reliable signal reception in a lightweight package.

Figura 1: LICHIFIT 4100E 2.4G 4-Channel Micro Receiver. This image shows the compact receiver board with its antenna and pin connectors.

2. Caratteristiche principali

• Compatibilità: Designed for JR / SPEKTRUM DSM2 transmitters (e.g., DX6I, DX7, DX8, DSX7, DSX9, DSX11).
• Modulazione: DSM2
• Banda: 2.4GHz
• Canali: 4
• Dimensioni compatte: Circa 29 mm x 16 mm x 7 mm.
• Leggero: Circa 3 g.
• Voltage Gamma: 3.6V - 10V.
• Lunghezza antenna: 29mm.

3. Setup and Binding Instructions

To establish communication between your LICHIFIT 4100E receiver and a compatible DSM2 transmitter, follow these binding steps:

1. Connect the Bind Plug: Insert the bind plug into the "BIND" port on the receiver. Ensure the plug is fully seated and correctly oriented. The negative pin is typically the furthest from the board.


Figura 2: Bind Plug. This plug is used to put the receiver into binding mode.

2. Alimentare il ricevitore: Connect a power source (e.g., battery or ESC with BEC) to any available channel port on the receiver. The receiver's LED should begin to flash rapidly, indicating it is in binding mode. If the LED only "blips" or does not flash, check the power connection and bind plug orientation. A steady LED indicates a successful connection, not binding mode.
3. Activate Transmitter Bind Mode: Turn on your compatible DSM2 transmitter while holding its bind button or activating its bind function (refer to your transmitter's manual for specific instructions).
4. Rilegatura completa: The receiver's LED should change from rapidly flashing to solid, indicating a successful bind.
5. Rimuovere il connettore di collegamento: Once the LED is solid, disconnect the power from the receiver, then remove the bind plug from the "BIND" port.
6. Prova di connessione: Reconnect power to the receiver (without the bind plug). The LED should illuminate solid, confirming the bind. Test all control surfaces and functions to ensure proper operation.

Nota: Some users have reported that the receiver may require re-binding if the battery is disconnected for an extended period or if the power cycle is interrupted during initial setup. Always verify the solid LED indicator after powering on.

4. Istruzioni per l'uso

After successful binding, connect your servos and Electronic Speed Controller (ESC) to the corresponding channels on the receiver. The LICHIFIT 4100E provides 4 channels for various control functions.

• Collegamenti dei canali: Connect servos for ailerons, elevator, rudder, and the ESC for throttle control to the appropriate channel pins. Refer to your model's specific wiring diagram.
• Sequenza di accensione: Always turn on your transmitter first, then power on the receiver. When powering off, disconnect power from the receiver first, then turn off the transmitter.
• Controllo della portata: Before flight or operation, perform a range check according to your transmitter's instructions to ensure a stable connection.

5. Manutenzione

Una corretta manutenzione garantisce la longevità e l'affidabilità delle prestazioni del ricevitore.

• Mantenere asciutto: The receiver is not water-resistant. Avoid exposure to moisture, humidity, and liquids.
• Pulizia: Mantenere il ricevitore libero da polvere, sporco e detriti. Utilizzare una spazzola morbida e asciutta o aria compressa per la pulizia.
• Protezione fisica: Protect the receiver from physical impact and vibrations. Mount it securely within your model.
• Cura dell'antenna: Ensure the antenna is not cut, kinked, or damaged. Proper antenna placement is crucial for optimal range.

6. Risoluzione Dei Problemi

• Receiver Not Binding / LED Blips:
  • Ensure the bind plug is fully inserted into the "BIND" port.
  • Verify the bind plug's orientation; the negative pin is typically furthest from the board.
  • Check power connections to the receiver. Ensure sufficient voltage (3.6-10 V).
  • Confirm your transmitter is in DSM2 mode and its bind function is correctly activated.
• Loss of Binding After Power Cycle:
  • Some units may require re-binding if power is disconnected. Perform the binding procedure again.
  • Ensure the bind plug is removed Prima disconnecting power after a successful bind.
• Nessuna risposta di controllo:
  • Verificare che il ricevitore sia stato associato correttamente (LED fisso).
  • Check all servo and ESC connections to the correct channels.
  • Verify that servos and ESCs are receiving power.
  • Ensure your transmitter is powered on and functioning correctly.
• Gamma limitata:
  • Check for damage to the receiver antenna.
  • Ensure the antenna is positioned optimally and not shielded by carbon fiber or metal components.
  • Evitare di utilizzare il dispositivo in aree con forti interferenze nella banda dei 2.4 GHz.

7. Specifiche

8. Garanzia e supporto

Information regarding product warranty and direct customer support for the LICHIFIT 4100E receiver was not provided in the available product data. Please refer to your retailer or point of purchase for specific warranty terms and support options.