RODOT DC 12V 1CH RF Wireless Relay Module Instruction Manual

1. Introduzione

The RODOT DC 12V 1CH RF Wireless Relay Module is a versatile remote control switch designed for various industrial and security applications. It offers stable and reliable performance with high receive sensitivity, allowing signals to pass through walls, floors, and doors. The maximum range is up to 164ft/50m in open areas. This module is compatible with EV1527 learning code remote controls operating at 433Mhz.

2. Contenuto della confezione

Il pacchetto include i seguenti componenti:

• 2 x 1-Button Transmitters (Remote Controls)
• 1 x 1CH Receiver Module
• 1 x Receiver Shell

Immagine: Contenuto della confezione del prodotto.

3. Prodotto finitoview

The system consists of a receiver module and remote controls. The receiver module is designed for easy integration into various setups, providing terminals for power input and relay output. The remote controls allow for flexible operation of the connected devices.

Image: The receiver module and two remote controls.

Immagine: dettagliata view of the receiver module's terminals.

4. Specifiche

5. Installazione e cablaggio

The receiver module requires a 12V DC power supply. Ensure correct polarity when connecting power. The module provides Normally Open (NO), Common (COM), and Normally Closed (NC) terminals for connecting your device.

Schema elettrico

Refer to the diagram below for typical wiring configurations. The power supply for the connected device can be any voltage, as the relay only controls the circuit's switch.

Image: Wiring diagram for the receiver module.

Definizioni terminali:

• COMUNICAZIONE: Terminale comune del relè.
• NO: Normally Open terminal of the relay. When the relay is not working, NO is disconnected from COM.
• NC: Normally Closed terminal of the relay. When the relay is not working, NC is connected to COM.
• V+: 12V Positive input.
• V-: 12V Negative input.

6. Operating Modes & Pairing

The relay module supports several operating modes, which can be configured by pressing the learning button on the receiver module a specific number of times. Always clear previous pairings before setting a new mode.

Clearing Paired Remote Controls:

Press the learning button 8 times. The indicator LED will flash, confirming all previously paired remote controls have been cleared.

Setting Operating Modes:

After clearing, press the learning button the specified number of times for your desired mode, then press a button on your remote control to pair.

• Modalità momentanea: Press the learning button 1 time. Press and hold the remote button to turn ON, release to turn OFF.
• Modalità di commutazione: Press the learning button 2 times. Press the remote button once to turn ON, press again to turn OFF.
• Modalità bloccata: Press the learning button 3 times. (Requires a 2-button remote). Press button A to turn ON, press button B to turn OFF.
• Modalità di ritardo: Press the learning button 4, 5, 6, or 7 times for 5s, 10s, 15s, or 20s delay respectively. Press the remote button to turn ON, it will automatically turn OFF after the set delay.

Image: Visual explanation of different working modes.

Modalità momentanea

Attiva/disattiva modalità

Modalità bloccata

Modalità di spegnimento ritardato

7. Risoluzione Dei Problemi

• Il telecomando non risponde: Ensure the receiver module is powered correctly (12V DC). Check if the remote control is paired to the receiver. If not, follow the pairing instructions.
• Gamma limitata: Ensure the antenna on the receiver module is extended and not obstructed. Environmental factors like thick walls or other RF interference can reduce range.
• Modalità di funzionamento non corretta: If the relay operates unexpectedly, re-clear all paired remotes and re-pair them in the desired operating mode.
• Il LED non si accende: Verify the power supply connections to the receiver module. Check the LED itself for damage.

8. Informazioni sulla sicurezza

• Scollegare sempre l'alimentazione prima di effettuare qualsiasi cablaggio o manutenzione.
• Assicurarsi che tutti i collegamenti siano ben saldi per evitare cortocircuiti.
• Non esporre il modulo all'umidità o a temperature estreme.
• This device is intended for low-voltage DC applications. Do not connect to AC power unless specified.

9. Garanzia e supporto

For any issues or questions regarding your RODOT DC 12V 1CH RF Wireless Relay Module, please contact RODOT DIY customer support. Refer to your purchase documentation for warranty details.