EASYGUARD ETO001 Foot Kick Trunk Tailgate Opener User Manual

1. Prodotto finitoview

The EASYGUARD ETO001 is a foot-activated system designed to open or close your vehicle's trunk or tailgate automatically. This system enhances convenience by allowing hands-free operation, particularly useful when your hands are full.

Important Prerequisites:

Your vehicle must be equipped with an original or aftermarket electric tailgate lift that can automatically pop up or close the trunk. This product will not function without an existing electric tailgate lift system.
Your vehicle should have an original or aftermarket smart key Passive Keyless Entry (PKE) system. This system allows the vehicle to automatically unlock or release the trunk when you approach it. If your vehicle lacks a PKE system, you must manually disarm or unlock the vehicle before using the foot kick function.

Illustration of a foot kicking under a car bumper to open the trunk, and a hand holding a smart key near a car with an open trunk.

Figure 1: Hands-free trunk operation via foot kick and smart key PKE system.

2. Compatibilità

The ETO001 system is designed for DC12V vehicles, including sedans, compact cars, SUVs, and MPVs. It is not compatible with DC24V vehicles.

Refer to the compatibility chart below to ensure your vehicle meets the necessary requirements for proper function.

Compatibility chart showing vehicle types (SUV, hatch-back, MPV, Sedan, compact) are compatible. It also details compatibility based on electric tailgate and PKE system presence.

Figure 2: Compatibility requirements for the ETO001 system.

Tipo di veicolo: SUV, Hatchback, MPV, Sedan, Compact (Compatible)
With Electric Tailgate + PKE: Approach & kick to pop up/close trunk (Compatible)
With Electric Tailgate but no PKE: Disarm/unlock first, then kick to pop up/close trunk (Compatible)
No Electric Tailgate: Cannot kick to pop up/close trunk (Not Compatible)

3. Componenti del prodotto

The EASYGUARD ETO001 system includes the following components:

Image showing two circular trunk sensor wires.

Figure 3: Trunk Sensors (x2)

Image showing the black control module with white connectors.

Figura 4: Modulo di controllo

Image showing the main wire harness with multiple colored wires and connectors.

Figure 5: Main Wire Harness

Figure 6: Backup Diodes

4. Istruzioni per l'installazione

Si raccomanda l'installazione da parte di un professionista. Assicurarsi che l'alimentazione del veicolo sia scollegata prima di iniziare l'installazione.

4.1 Control Module Placement

The control module should be installed in a secure location, preferably within the bumper area.
NON FARE stick the control module or sensing wires on any metal part or anti-collision pipe. Metal interference can significantly reduce sensing performance.
The control module is IP67 waterproof; however, NON FARE open its housing.

4.2 Sensor Wire Installation

The sensing wires are crucial for detecting foot movement. Proper placement is essential for reliable operation.

Diagram showing two sensors installed parallel, 4-6 inches apart, at least 2 inches from the ground, under the bumper. It also illustrates correct and incorrect foot kicking motions.

Figure 7: Sensor installation guidelines and foot kick technique.

The two sensing wires should be installed parallel to each other.
Maintain a distance of 4-6 inches (10-15 cm) between the two sensing wires.
The sensors should be positioned at least 2 inches (5 cm) from the ground.
For optimal performance, ensure the sensing wires are not installed on metal parts. If your car has many metal parts in the bumper area, adjust the placement to find the best sensing effect.

Diagram showing black and gray connector sensing wires routed along the top edge of the bumper, and a person kicking under the bumper with a sensor detecting range of 19.69 inches (50 cm).

Figure 8: Routing of sensing wires and effective sensor detection range.

Note di installazione importanti:

The sensor detecting range is approximately 19.69 inches (50 cm). Ensure your foot is within this range when performing the kick action.
When installing, lift your foot and kick towards the middle of the rear bumper. Your foot should be 8-15 cm from the bumper.
Keep the sensor away from any metal parts or anti-collision pipes as far as possible to prevent interference.

5. Istruzioni per l'uso

Once installed correctly, operate the ETO001 system as follows:

5.1 Apertura del bagagliaio

Ensure the vehicle's ACC (Accessory) power is turned off.
Disarm the car. If your vehicle has a smart key PKE system, the trunk will automatically unlock as you approach. If not, manually unlock the vehicle first.
Kick your foot under the detect sensor within 1 meter of the car's rear bumper. Perform a quick forth-and-back motion (as shown in Figure 7).
The trunk will automatically pop up/open.

5.2 Closing the Trunk

With the trunk open, perform the same foot kick action under the detect sensor.
The electric tailgate will automatically close. This function requires an electric tailgate lift system.

5.3 Linee guida per l'utilizzo

The foot-lifting and foot-lowering action must be completed within 1 second. Incorrect timing may be treated as a wrong signal by the system.
After each successful foot kick, wait at least 20 seconds before performing another kick action. This prevents unintended repeated operations.
The smart key should be within 1 meter of the car's rear bumper for the system to function correctly (if PKE is used).

6. Manutenzione

The EASYGUARD ETO001 system is designed for durability and requires minimal maintenance.

Mantenere puliti i sensori: Periodically inspect the sensor area under the bumper and clean off any dirt, mud, or debris that may accumulate. Excessive build-up can interfere with sensor detection.
Evitare danni fisici: Ensure the control module and sensing wires are protected from physical impact or damage.
Do Not Open Control Module: The control module is sealed and IP67 waterproof. Opening the housing will void the warranty and may damage the internal components.

7. Risoluzione Dei Problemi

If you experience issues with your ETO001 system, refer to the following troubleshooting guide:

Problema	Possibile causa	Soluzione
Trunk does not open/close with foot kick.	Vehicle lacks electric tailgate lift. Vehicle not disarmed/unlocked (no PKE or PKE out of range). Incorrect foot kick motion or timing. Sensors obstructed or improperly installed. Too soon after previous kick.	Verify vehicle has electric tailgate lift. Ensure vehicle is disarmed/unlocked. If PKE, ensure smart key is within 1 meter. Perform a quick forth-and-back kick within 1 second. Check sensor placement (not on metal, 4-6 inches apart, >2 inches from ground). Clean sensors. Wait at least 20 seconds between kick attempts.
Trunk opens/closes unintentionally.	Sensor sensitivity too high or improper placement. Interference from metal objects or other vehicle systems.	Re-evaluate sensor placement, ensuring it's not too close to the ground or metal parts. Ensure control module and sensing wires are not stuck on metal parts or anti-collision pipes.
System not responding at all.	Problema di collegamento elettrico. Componente difettoso.	Check all wiring connections to ensure they are secure and correctly installed. Contact customer support if all other troubleshooting steps fail.

8. Specifiche

Caratteristica	Specificazione
Numero di modello	ETO001
Volume di eserciziotage	DC12V (Not compatible with DC24V)
Grado di impermeabilità	IP67 (Control Module)
Materiale	Metallo
Usi specifici	Automobiles (Sedan, Compact, SUV, MPV)
Campo di rilevamento del sensore	Circa 19.69 pollici (50 cm)

Image showing various car types (sedan, SUV, MPV) and a car driving through water, highlighting IP67 waterproof control module.

Figure 9: ETO001 compatibility with various vehicle types and IP67 waterproof feature.

9. Garanzia e supporto

9.1 Informazioni sulla garanzia

The EASYGUARD ETO001 comes with a Garanzia del produttore di 1 anni dalla data di acquisto. La presente garanzia copre i difetti di materiali e di fabbricazione in condizioni di normale utilizzo. Non copre i danni causati da installazione impropria, uso improprio, incidenti o modifiche non autorizzate.

9.2 Assistenza clienti

For technical assistance, warranty claims, or any questions regarding the EASYGUARD ETO001, please contact your retailer or the manufacturer directly. When contacting support, please have your product model number (ETO001) and proof of purchase readily available.

Manufacturer: ieasyguard.com