Mount-It! MI-766 Dual Monitor Wall Mount Instruction Manual

1. Introduzione

This instruction manual provides comprehensive guidance for the safe and effective installation, operation, and maintenance of your Mount-It! MI-766 Dual Monitor Wall Mount. This mount is designed to support two monitors up to 27 inches each, featuring full motion articulation and a gas spring system for easy adjustments. Please read this manual thoroughly before installation and retain it for future reference.

2. Informazioni sulla sicurezza

AVVERTIMENTO: La mancata lettura e osservanza di tutte le istruzioni può causare lesioni personali o danni materiali. Il produttore non è responsabile per danni o lesioni causati da un montaggio o un utilizzo non corretti.

• Ensure the mounting surface can safely support the combined weight of the mount and monitors.
• Non superare la capacità di peso massima di 14.4 libbre (6.5 kg) per braccio.
• Questo prodotto è destinato esclusivamente all'uso in ambienti interni.
• Use appropriate safety equipment and tools during installation.
• In caso di dubbi su qualsiasi fase del processo di installazione, consultare un professionista qualificato.
• Tenere lontani bambini e animali domestici durante l'installazione.

3. Contenuto della confezione

Verify that all components are present and undamaged before beginning installation. If any parts are missing or damaged, contact Mount-It! customer service.

• Dual Monitor Wall Mount Assembly
• Piastre VESA (2)
• Mounting Hardware Kit (screws, washers, anchors for various wall types)
• Chiavi esagonali per le regolazioni
• Manuale di istruzioni

4. Configurazione e installazione

Before installation, determine your wall type (wood stud, concrete, or brick) and ensure it can support the weight. A stud finder and level are recommended.

Figure 4.1: Mount-It! MI-766 Dual Monitor Wall Mount

4.1. Wood Stud Mounting

1. Locate the Stud: Use a stud finder to locate the center of a wood stud at your desired mounting height.
2. Segnare i fori pilota: Hold the wall mount against the wall, ensuring it is level. Mark the center of the mounting holes with a pencil.
3. Praticare i fori pilota: Drill pilot holes using a 3/16 inch (4.5 mm) drill bit to a depth of 2.2 inches (55 mm).
4. Fissare il supporto alla parete: Secure the wall mount to the wall using the provided lag screws and washers. Tighten until secure, but do not overtighten.

4.2. Concrete or Brick Wall Mounting

1. Segnare i fori pilota: Hold the wall mount against the wall, ensuring it is level. Mark the center of the mounting holes with a pencil.
2. Praticare i fori pilota: Drill pilot holes using a 3/8 inch (10 mm) drill bit to a depth of 2.4 inches (60 mm).
3. Inserisci ancore: Insert the concrete anchors into the drilled pilot holes.
4. Fissare il supporto alla parete: Secure the wall mount to the wall using the provided lag screws and washers. Tighten until secure, but do not overtighten.

4.3. Attaching Monitors to VESA Plates

Figure 4.2: Detachable VESA Plate and Adjustment Ranges

1. Prepare Monitor: Place your monitor face down on a soft, clean surface. Select the appropriate size mounting bolts and washers for your monitor's VESA holes (75x75mm or 100x100mm).
2. Install Top Bolts: Install the top two bolts and washers into the monitor's VESA holes, leaving a gap of approximately 0.11 inches (3 mm) between the screw head and the monitor surface.
3. Monitor sospeso: Carefully hang the monitor onto the top of the VESA plate on the arm, ensuring the top bolts slide into the keyhole slots.
4. Install Lower Bolts: Install the lower two bolts and washers through the lower VESA holes and tighten all four bolts until secure. Do not overtighten.
5. Ripetere l'operazione per il secondo monitor.

4.4. Gestione dei cavi

To maintain a tidy workspace, route your monitor cables through the integrated cable management system.

1. Rimuovere le coperture: Use the provided hex wrench to remove the bolts securing the cable management covers on the underside of each arm. Gently pull the covers away.
2. Cavi del percorso: Route your monitor cables (power, video, etc.) along the arm channels.
3. Sostituire le coperture: Replace the covers and secure them with their bolts.

5. Funzionamento e regolazioni

The Mount-It! MI-766 offers a range of adjustments to achieve optimal viewangolazioni e posizionamento ergonomico.

Figure 5.1: Dual monitor setup with the MI-766 wall mount.

5.1. Regolazione della tensione della molla a gas

The gas spring system allows for effortless height adjustment. The tension needs to be calibrated to your monitor's weight.

Figure 5.2: Gas Spring Tension Adjustment points.

1. Access Tension Bolt: Position the monitor horizontally. Lift the arm slightly to access the tension adjustment bolt located on the arm.
2. Regola la tensione: Use the provided hex wrench to adjust the tension:
   • Ruotare counter-clockwise (towards '+') for heavier monitors (to increase tension).
   • Ruotare clockwise (towards '-') for lighter monitors (to decrease tension).
3. Regolazione del test: Continue adjusting until the arm stays in place when you move the monitor to different heights.

5.2. Height, Swivel, Tilt, and Rotation

Figure 5.3: Gas Spring Hovering System allows for easy tilt adjustments.

• Regolazione dell'altezza: Once the gas spring tension is correctly set, you can raise or lower your monitors by hand to your desired ergonomic height.
• Girevole: The monitor arms can swivel up to 90 degrees left or right from the central mounting point, allowing for flexible positioning.
• Inclinazione: Monitors can be tilted from +90 degrees to -45 degrees to reduce glare and optimize viewing angles. If the monitor droops or won't hold its angle, tighten the side bolts on the VESA plate connection.
• Rotazione: Each monitor can be rotated 360 degrees, allowing for landscape or portrait orientation.

Figure 5.4: Monitors can rotate 360 degrees for portrait or landscape viewing.

6. Manutenzione

Una manutenzione regolare garantisce la longevità e il funzionamento sicuro del supporto per monitor.

• Pulizia: Pulisci il supporto con un panno morbido eamp panno. Evitare detergenti abrasivi o solventi.
• Ispezione: Controllare periodicamente tutte le viti e i collegamenti per assicurarsi che siano ben serrati e sicuri. Serrare nuovamente se necessario.
• Molla a gas: If the gas spring tension feels off, re-adjust it according to the instructions in Section 5.1.

7. Risoluzione Dei Problemi

If you encounter issues with your Mount-It! MI-766, refer to the following common problems and solutions.

• Monitor is drooping or not holding its height:
  • The gas spring tension may be too low for your monitor's weight. Increase the gas spring tension (rotate counter-clockwise) as described in Section 5.1.
• Monitor is difficult to move or stays too high:
  • The gas spring tension may be too high for your monitor's weight. Decrease the gas spring tension (rotate clockwise) as described in Section 5.1.
• Monitor tilts unexpectedly or won't hold its tilt angle:
  • Tighten the side bolts on the VESA plate connection that control the tilt mechanism.
• Mount feels unstable on the wall:
  • Ensure all lag screws securing the mount to the wall are fully tightened. Re-check the wall type and ensure appropriate anchors/stud mounting was used. If unsure, consult a professional.

8. Specifiche

Figure 8.1: Supported monitor size and weight capacity.

Figure 8.2: The mount is compatible with brick, concrete, and wood walls.

9. Garanzia e supporto

Mount-It! products are backed by a limited warranty. For specific warranty details, product support, or to purchase replacement parts, please visit the official Mount-It! websito o contattare il loro servizio clienti.

Supporto online: Visit the Mount-It! Store on Amazon