Introduzione
The ChongXiao Brushless Square Wave Controller with LCD Display is an electronic device designed for electric scooters and electric bicycles. It provides control over speed and direction, and its integrated display instrument allows users to monitor the operating status of their vehicle. This brushless design ensures smoother operation, enhanced stability, and a longer lifespan. The controller incorporates advanced technology for reliable performance and durability, contributing to the safety and stability of your electric vehicle.
Cosa c'è nella scatola
- Controller senza spazzole
- LCD Display (Thumb Display)
Specifiche
| Marca | ChongXiao |
| Nome del modello | 1000W 1200W 1500W brushless controller with thumb display |
| Volume Nominaletage Gamma | 36V, 48V, 60V |
| Potenza massima in uscita | 1000W, 1200W, 1500W |
| Corrente massima | 34A, 36A, 40A |
| Tipo di articolo | Controller senza spazzole |
| Usi consigliati | Repair/Replacement, Upgrade |
| Stile del freno | Thumb Brake and Regenerative |
| Materiale | Alluminio (telaio) |
Istruzioni di installazione
Careful installation is crucial for the proper function and safety of your electric bike or scooter. Ensure the vehicle is powered off before beginning any installation steps.
Controllore finitoview
Image: The red casing of the ChongXiao Brushless Square Wave Controller.
The controller features a robust red aluminum casing designed for heat dissipation and protection. Ensure it is mounted in a location that allows for adequate airflow and is protected from direct water exposure.
Dimensioni
Image: Diagram showing the dimensions of the controller: 212mm length, 88mm width, 48mm height.
Before installation, verify that the controller's dimensions (approximately 212mm x 88mm x 48mm) fit within the available space on your electric bike or scooter.
Collegamenti elettrici
Image: Detailed wiring diagram for the controller, labeling each connector.
Refer to the wiring diagram above for correct connections. Each numbered connection corresponds to a specific function:
- High-level Brake: Connect to the high-level brake signal.
- Brake Light Power: Connect to the brake light power supply.
- Throttle Handle: Connect to the throttle input.
- Retromarcia: Connect for reverse function (if applicable).
- Freno basso: Connect to the low-level brake signal.
- Hall (5 wires): Collegare ai fili del sensore Hall del motore.
- Linear Brake (Thumb Brake): Connect to the thumb brake lever.
- PAS (Sistema di pedalata assistita): Connect to the PAS sensor.
- Head Light/Tail Light Power: Connect for vehicle lighting.
- Regenerative Brake: Connect for regenerative braking function.
- Intelligent Recognition (Self-learning): Used for initial motor pairing.
- LCD: Connect to the LCD display unit.
- Accendi: Connect to the ignition switch.
- XT60 Battery: Connect to the main battery power supply (XT60 connector).
- Phase Line: Collegare ai fili di fase del motore.
Thumb Display Installation
Image: The thumb display unit with its mounting bracket and cable.
Mount the thumb display securely on your handlebar using the provided bracket. Ensure it is within easy reach for operation and visibility. Connect the display cable to the 'LCD' port on the controller.
Self-Learning Function
After all connections are made, use the 'Intelligent Recognition' (self-learning) wires to pair the controller with your motor. Typically, you connect these two wires, power on the system, and the motor will spin. If it spins in the wrong direction, disconnect, reconnect, and power on again. Once the motor spins correctly, disconnect the self-learning wires. This process helps the controller learn the motor's phase and Hall sensor configuration.
Istruzioni per l'uso
Once installed and powered on, the LCD display will show key operating parameters.
Accensione/spegnimento
Press and hold the power button on the LCD display to turn the system on or off. Ensure all connections are secure before powering on.
Funzioni di visualizzazione
Il display LCD in genere mostra:
- Velocità attuale
- Indicatore del livello della batteria
- Livello di assistenza (PAS)
- Distanza percorsa / Contachilometri
- Codici di errore (se presenti)
Use the buttons on the display to cycle through different information screens or adjust settings like assistance level.
Throttle and Braking
The thumb throttle controls motor power. Apply the throttle gradually for smooth acceleration. The brake levers (including regenerative brake if connected) will cut motor power and activate braking functions.
Manutenzione
Regular maintenance helps ensure the longevity and optimal performance of your controller and display.
- Mantenere pulito: Wipe the controller and display with a dry or slightly damp stoffa. Evitare l'uso di prodotti chimici aggressivi o di acqua eccessiva.
- Controllare le connessioni: Ispezionare periodicamente tutti i collegamenti elettrici per assicurarsi che siano saldi e privi di corrosione o danni. Collegamenti allentati possono causare un funzionamento intermittente o guasti al sistema.
- Evitare l'esposizione all'acqua: While the controller may have some water resistance, it is not fully waterproof. Avoid submerging the unit or exposing it to heavy rain for extended periods.
- Temperatura: Operate and store the unit within recommended temperature ranges to prevent damage to electronic components.
Risoluzione dei problemi
In caso di problemi, fare riferimento ai seguenti passaggi comuni per la risoluzione dei problemi:
- Nessuna alimentazione al display/controller:
- Check battery connection (XT60).
- Ensure the ignition wire (if used) is properly connected and switched on.
- Verify the main power cable from the battery to the controller is intact.
- Il motore non risponde:
- Check motor phase wires and Hall sensor wires for secure connection.
- Ensure the throttle handle is connected correctly.
- Perform the self-learning function again if the motor was recently installed or reconnected.
- Controllare eventuali codici di errore sul display LCD.
- Velocità/potenza di uscita non corrette:
- Verificare il vol della batteriatage matches the controller's supported range (36V/48V/60V).
- Ensure the display settings (e.g., wheel size, speed limit) are correctly configured.
- Il display non funziona correttamente:
- Check the connection between the LCD display and the controller.
- Ensure the display itself is not damaged.
Se questi passaggi non risolvono il problema, contattare l'assistenza clienti.
Informazioni sulla garanzia
This product comes with a Limited Warranty. Specific details regarding the terms and conditions of this warranty are not provided in the product information. Please retain your proof of purchase for any warranty claims.
Assistenza clienti
For further assistance, technical support, or warranty inquiries, please contact the seller or manufacturer directly through the platform where the product was purchased. Provide your product model number and purchase details when contacting support.