PWAY HDMI Extender RX Only Instruction Manual

1. Introduzione

This manual provides instructions for the PWAY HDMI Extender Receiver (RX) unit, Model B0C36TPYL4. This receiver is designed to work exclusively with the PWAY PW-DT243 HDMI Extender Transmitter (TX) unit to extend HDMI signals over a single Cat5e/6/7 Ethernet cable. It supports both one-to-one direct connections and one-to-many configurations via a dedicated Gigabit Ethernet switch.

2. Contenuto della confezione

Si prega di verificare che tutti gli articoli siano presenti nel pacco:

• PWAY HDMI Extender Receiver (RX) Unit
• Power Adapter for RX Unit

Image 2.1: Package contents showing the PWAY HDMI Extender Receiver and its power adapter.

3. Prodotto finitoview

The PWAY HDMI Extender Receiver features essential ports and indicators for connectivity and status monitoring.

Immagine 3.1: Anteriore e posteriore views of the PWAY HDMI Extender Receiver, highlighting the UTP (Ethernet), DC5-12V (Power Input), PWR (Power Indicator), STA (Status Indicator), and HD OUT (HDMI Output) ports.

Descrizione delle porte e degli indicatori:

• UTP: RJ45 port for connecting to the Ethernet cable (Cat5e/6/7) from the Transmitter or Gigabit switch.
• CC 5-12 V: Porta di ingresso alimentazione per l'adattatore di alimentazione incluso.
• PWR: Power indicator LED. Illuminates when the device is powered on.
• STA: Status indicator LED. Indicates signal status (e.g., blinking for activity, solid for stable connection).
• USCITA HD: HDMI output port for connecting to a display device (monitor, TV).

4. Impostazione

The PWAY HDMI Extender RX unit can be configured in two primary ways: one-to-one direct connection or one-to-many via a Gigabit switch.

4.1. One-to-One Direct Connection

This configuration extends an HDMI signal from a single transmitter to a single receiver over a dedicated Ethernet cable.

1. Connect an HDMI cable from your source device (e.g., PC, media player) to the HDMI IN port on the PWAY HDMI Extender Transmitter (PW-DT243).
2. Connect one end of a Cat5e/6/7 Ethernet cable to the UTP port on the Transmitter.
3. Connect the other end of the Cat5e/6/7 Ethernet cable to the UTP port on the PWAY HDMI Extender Receiver (RX). Ensure the cable length does not exceed 500 feet (150 meters) for optimal performance.
4. Connect an HDMI cable from the HD OUT port on the Receiver to the HDMI input of your display device (e.g., monitor, TV).
5. Connect the included power adapters to both the Transmitter and Receiver units, then plug them into power outlets.
6. Power on all connected devices. The PWR and STA indicators on both units should illuminate, indicating a successful connection.

Image 4.1: Diagram illustrating a one-to-one HDMI extension setup, connecting a source to a display via a Transmitter, Cat5e/6 cable, and Receiver.

4.2. One-to-Many Connection via Gigabit Switch

This configuration allows a single transmitter to send an HDMI signal to multiple receivers and displays through a Gigabit Ethernet switch.

1. Connect an HDMI cable from your source device to the HDMI IN port on the PWAY HDMI Extender Transmitter (PW-DT243).
2. Connect a Cat5e/6/7 Ethernet cable from the UTP port on the Transmitter to an available port on a dedicated Gigabit Ethernet switch.
3. For each PWAY HDMI Extender Receiver (RX) unit, connect a Cat5e/6/7 Ethernet cable from its UTP port to an available port on the same Gigabit Ethernet switch.
4. Connect an HDMI cable from the HD OUT port of each Receiver to its respective display device.
5. Connect the included power adapters to the Transmitter and all Receiver units, then plug them into power outlets. Power on the Gigabit switch and all connected devices.
6. Importante: Use an unmanaged or dedicated Gigabit switch. If using a Smart Gigabit Switch, configure VLANs to isolate video traffic from other network traffic to prevent interference. Do not connect to your home internet router or a shared network switch, as this can cause signal issues and network performance degradation.

Image 4.2: Diagram illustrating a one-to-many HDMI extension setup, where a single Transmitter feeds multiple Receivers and displays via a Gigabit Ethernet switch.

5. Istruzioni per l'uso

Once the setup is complete and all devices are powered on, the PWAY HDMI Extender system should operate automatically.

• Ensure the PWR LED on the receiver is solid, indicating it is receiving power.
• The STA LED on the receiver should indicate a stable connection to the transmitter. If it is blinking or off, check all cable connections and power.
• The extended HDMI signal should appear on the connected display(s) without delay.

6. Risoluzione Dei Problemi

If you encounter issues with your PWAY HDMI Extender system, refer to the following troubleshooting steps:

• Nessuna immagine o segnale intermittente:
  • Verify that both the Transmitter and Receiver units are powered on and their respective PWR LEDs are illuminated.
  • Check all HDMI cable connections between source, transmitter, receiver, and display. Ensure they are securely plugged in.
  • Inspect the Cat5e/6/7 Ethernet cable for damage and ensure it is properly terminated and securely connected to both the Transmitter and Receiver (or Gigabit switch).
  • Ensure the Ethernet cable length does not exceed the maximum recommended distance of 500 feet (150 meters).
  • If using a Gigabit switch for one-to-many setup, confirm it is a dedicated or unmanaged switch. If it's a smart switch, verify VLAN configuration isolates the video traffic. Avoid using home routers or shared network switches.
  • Test with a different HDMI cable or Ethernet cable if possible.
  • Power cycle all devices (source, transmitter, receiver, display, and switch) by unplugging and replugging their power adapters.
• Compatibility Issues with Existing Setups:
  • Be aware that hardware revisions can occur. If you are expanding an existing PWAY HDMI Extender system, ensure the new RX unit is compatible with your existing TX unit. Mixing different hardware revisions may lead to incompatibility. It is recommended to purchase units from the same batch or as a complete set when expanding.

7. Specifiche

8. Manutenzione

To ensure the longevity and optimal performance of your PWAY HDMI Extender Receiver, follow these maintenance guidelines:

• Conservare il dispositivo in un luogo fresco e asciutto, lontano dalla luce solare diretta, da temperature elevate e dall'umidità.
• Pulire l'unità con un panno morbido e asciutto. Non utilizzare detergenti liquidi o spray.
• Evitare di posizionare oggetti pesanti sull'unità.
• Garantire un'adeguata ventilazione attorno al dispositivo per evitare il surriscaldamento.

9. Garanzia e supporto

PWAY products are designed for reliability and performance. For specific warranty information, please refer to the documentation included with your purchase or visit the official PWAY website. If you require technical assistance or have questions not covered in this manual, please contact PWAY customer support through their official channels.