1. Introduzione
This manual provides essential information for the safe and effective operation of your FLIPSKY 75100 Pro V2.0 Speed Controller. Please read this manual thoroughly before installation and use to ensure optimal performance and longevity of the device.
The FLIPSKY 75100 Pro V2.0 is an advanced Electronic Speed Controller (ESC) designed for electric skateboards, scooters, and e-bikes. It features an aluminum PCB for enhanced heat dissipation and supports various control modes and sensor types.
2. Informazioni sulla sicurezza
- Scollegare sempre l'alimentazione prima di effettuare qualsiasi installazione, manutenzione o modifica del cablaggio.
- Ensure all connections are secure and correctly polarized to prevent damage to the ESC or other components.
- Utilizzare l'ESC entro il volume specificatotage and current limits to avoid overheating and component failure.
- Tenere l'ESC lontano da acqua, umidità e temperature estreme.
- Installation should be performed by individuals with adequate knowledge of electronics and electrical systems.
- Regularly inspect wiring and connections for signs of wear or damage.
3. Caratteristiche del prodotto
The FLIPSKY 75100 Pro V2.0 ESC incorporates several key features for robust and flexible performance:
- Firmware: 6.02 (firmware update supported)
- Adjustable protection against: low voltage, alto volumetage, over current, temperature abnormal, MOSFETs/motor over temperature.
- Support for BLDC square wave mode control and FOC sine wave mode.
- Aluminum PCB for enhanced heat dissipation and extended lifespan.
- Programmable functionality.
- Regenerative braking capacity.
- Integrated power switch button (Red).
Figure 1: FLIPSKY 75100 Pro V2.0 Speed Controller with various connection wires and power button.
4. Configurazione e connessioni
Proper connection of the ESC is critical for its functionality and safety. Refer to the connection diagram below for guidance.
Figure 2: Connection diagram illustrating battery, motor, and control signal ports.
4.1. Collegamenti di alimentazione
- Batteria: Connect your battery pack to the main power input wires (red for positive, black for negative). Ensure correct polarity. The ESC supports 14-84V (4-20S) input.
- Motore: Connect the three motor phase wires to the corresponding output wires from the ESC. The wires are typically black and do not require specific phase matching; the ESC will handle it.
- Interruttore di alimentazione: Connect the red power switch button to its designated port.
4.2. Collegamenti di controllo e sensori
- Sensori HALL: Connect the motor's HALL sensor wires to the HALL port on the ESC. Supported sensors include ABI, HALL, AS5047, AS5048A.
- PPM/PWM: For throttle input, connect your receiver's PPM/PWM signal to the PPM port.
- Bus CAN: Use the CAN port for communication between multiple ESCs (master/slave configuration) or other CAN-enabled devices.
- UART: The UART port allows for communication with external modules like Bluetooth modules or other microcontrollers.
- USB: Connect the ESC to a computer via the USB port for configuration and firmware updates using VESC Tool software.
- ADC: Analog-to-Digital Converter ports are available for various analog inputs.
Importante: When unplugging connectors, press the release tab to avoid damaging wires or the connector itself.
5. Istruzioni per l'uso
After successful installation and configuration using the VESC Tool, the ESC is ready for operation.
- Accensione: Press the red power switch button to turn on the ESC. The LED indicator will illuminate.
- Controllo dell'acceleratore: Apply throttle input via your connected PPM/PWM device. The ESC will control the motor speed and direction based on your input and configured settings.
- Frenata: The ESC supports regenerative braking. Applying reverse throttle will engage braking, which also recharges the battery to some extent.
- Monitoraggio: Use the VESC Tool connected via USB or UART (e.g., Bluetooth module) to monitor real-time parameters such as motor RPM, current, voltage, e la temperatura.
- Spegni: Press and hold the red power switch button to turn off the ESC.
6. Manutenzione
- Ispezione regolare: Controllare periodicamente tutti i cablaggi e i connettori per verificare la presenza di segni di usura, corrosione o collegamenti allentati.
- Pulizia: Keep the ESC clean and free from dust, dirt, and debris. Use a soft, dry brush or compressed air. Avoid using liquids.
- Gestione del calore: Ensure adequate airflow around the ESC, especially during high-power operation, to utilize its aluminum PCB's heat dissipation capabilities effectively.
- Aggiornamenti del firmware: Check for and apply firmware updates periodically using the VESC Tool to benefit from performance improvements and bug fixes.
7. Risoluzione Dei Problemi
| Problema | Possibile causa | Soluzione |
|---|---|---|
| L'ESC non si accende. | No power from battery, faulty power switch, incorrect wiring. | Controllare il volume della batteriatage, inspect power switch connection, verify main power wiring. |
| Il motore non gira o ha un comportamento irregolare. | Incorrect motor detection, loose motor phase wires, sensor issues, incorrect VESC Tool configuration. | Perform motor detection in VESC Tool, check motor wire connections, inspect sensor wiring, review VESC Tool settings. |
| ESC overheating. | Excessive load, insufficient cooling, short circuit, incorrect current limits. | Reduce load, ensure adequate airflow, check for shorts, adjust current limits in VESC Tool. |
| Nessuna risposta dell'acceleratore. | PPM/PWM signal not connected, incorrect receiver settings, VESC Tool input configuration error. | Verify PPM/PWM connection, check receiver output, configure input in VESC Tool. |
8. Specifiche
| Caratteristica | Dettaglio |
|---|---|
| Firmware | 6.02 (firmware update supported) |
| Dimensioni (L*W*H) | 103mm * 58mm * 27.7mm |
| Voltage Gamma | 14-84 V (4-20 secondi) |
| Corrente continua | 100A |
| Uscita BEC | 5V @ 1.5A |
| Modalità di controllo | BLDC square wave, FOC sine wave |
| ERPM massimo | 150000 |
| Porte di interfaccia di controllo | USB, CAN, UART |
| Sensori supportati | ABI, HALL, AS5047, AS5048A |
| Supporto del set di input | PPM, ADC, NRF, UART |
| Dimensioni del filo | 10AWG (75100 Pro) |
| Programmabile | SÌ |
| Capacità rigenerativa | SÌ |
| Filtro di fase | SÌ |
| Pulsante di accensione | Rosso |
| Materiale | Alluminio |
| Peso dell'articolo | 0.3 chilogrammi |
Figure 3: Dimensions of the FLIPSKY 75100 Pro V2.0 Speed Controller.
9. Garanzia e supporto
9.1. Informazioni sulla garanzia
The FLIPSKY 75100 Pro V2.0 Speed Controller comes with a warranty of 2 months or more, as specified by the manufacturer. Please retain your proof of purchase for warranty claims. The warranty covers manufacturing defects under normal use conditions. Damage resulting from improper installation, misuse, modification, or exceeding specified limits may void the warranty.
9.2. Supporto tecnico
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact FLIPSKY customer support through their official website or the retailer from whom the product was purchased. Ensure you have your product model number and purchase details ready.
10. Prodotto aggiuntivo Views
Figura 4: Un altro view of the FLIPSKY 75100 Pro V2.0 with connected wires.
Figura 5: in alto view of the FLIPSKY 75100 Pro V2.0, highlighting the ports and branding.
Figura 6: lato view of the FLIPSKY 75100 Pro V2.0, showcasing the ribbed aluminum casing per la dissipazione del calore.
Figura 7: Angolato view of the FLIPSKY 75100 Pro V2.0.
Figura 8: Fronte view of the FLIPSKY 75100 Pro V2.0.
Figura 9: Interno view of the FLIPSKY 75100 Pro V2.0 circuit board, showing components and capacitors.
Non sono stati trovati video ufficiali del prodotto del venditore rilevanti da incorporare in questo manuale.
