Peakmeter PM6819A Multifunctional Wire Tracker Instruction Manual

1. Introduzione

The Peakmeter PM6819A is a handheld, multifunctional cable line tester designed for comprehensive wire tracking and testing. This instrument is essential for telecommunication engineers, wiring engineers, and network maintenance personnel. It efficiently detects and traces various cable types, including RJ45, RJ11, telephone lines, and LAN network cables, both underground and within walls. Its capabilities include continuity testing, line finding, and identifying cable breaks.

2. Informazioni sulla sicurezza

Si prega di leggere attentamente tutte le istruzioni di sicurezza prima di utilizzare il dispositivo. La mancata osservanza di queste istruzioni può causare scosse elettriche, incendi o lesioni personali.

• Non utilizzare il dispositivo se appare danneggiato o funziona in modo anomalo.
• Ensure correct battery installation and replacement.
• Avoid contact with live circuits unless specifically designed for such testing and appropriate safety measures are in place.
• The device is rated CE CAT.III 600V RoHS. Adhere to these safety standards during operation.
• Tenere il dispositivo lontano dall'acqua e da temperature estreme.

3. Prodotto finitoview e componenti

The PM6819A consists of two main units: an Emitter (Transmitter) and a Receiver. Each unit has specific functions and ports for various testing scenarios.

Figura 1: The PM6819A Emitter and Receiver units, demonstrating various applications such as tracing cables near a fence, buried pipes, in-wall wiring, underfloor heating, and garden wiring.

Emitter Unit

• Porta RJ45: For connecting to Ethernet cables.
• Porta RJ11: Per il collegamento alle linee telefoniche.
• Cavo con morsetto a coccodrillo: For connecting to other types of wires for tracing.
• Pulsante di accensione: To turn the emitter on/off.
• Selezione della modalità: To switch between digital and analog signal modes.
• Porta di ricarica: Per ricaricare la batteria interna.

Unità ricevente

• Sonda: The elongated tip used to detect the signal from the emitter.
• Manopola di regolazione della sensibilità: To adjust the detection sensitivity.
• Pulsante di accensione: Per accendere/spegnere il ricevitore.
• Jack per cuffie: For connecting headphones for clearer audio signal detection in noisy environments.
• Indicatori LED: For signal strength and low voltage avvisi.

Figura 2: The receiver unit with a headphone jack, allowing for private and clearer audio detection during operation.

4. Specifiche

The following table details the technical specifications of the Peakmeter PM6819A.

Figura 3: Detailed specifications and features of the PM6819A device.

5. Impostazione

5.1 Installazione della batteria

• Emettitore: The emitter unit is powered by a rechargeable 3.7V lithium battery. Ensure it is charged using the provided charging cable before first use. The low voltage indicator LED will flash when the battery is below 3.7V.
• Ricevitore: The receiver unit requires one 9V 6LR61 battery. Open the battery compartment on the back of the receiver, insert the 9V battery with correct polarity, and close the compartment. The low voltage indicator LED will flash when the battery is below 9V.

5.2 Cavi di collegamento

• For RJ45/RJ11 Cables: Connect one end of the network or telephone cable directly to the corresponding RJ45 or RJ11 port on the emitter unit.
• For Other Wires: Use the provided alligator clip cable. Connect the alligator clips to the two ends of the wire you wish to trace.

6. Istruzioni per l'uso

6.1 Accensione

Press the power button on both the Emitter and Receiver units to turn them on. Ensure the indicator lights illuminate.

6.2 Wire Tracing (Digital Mode for RJ45/RJ11)

1. Connect the RJ45 or RJ11 cable to the emitter's corresponding port.
2. Set the emitter to Digital Signal Mode (multifrequency pulse).
3. Turn on the receiver and adjust its sensitivity.
4. Move the receiver's probe along the suspected path of the cable. The receiver will emit an audible tone and/or illuminate LEDs when it detects the signal. The tone will be strongest directly over the cable.
5. For underground cables, the detection depth is up to 2 meters.

Figura 4: The PM6819A receiver unit tracing an underground cable in a garden, indicating a detection range of 23.7 inches (approximately 0.6 meters) for effective localization.

6.3 Wire Tracing (Analog Mode for Other Wires)

1. Connect the alligator clips from the emitter to the wire you want to trace.
2. Set the emitter to Analog Signal Mode (audio pulse).
3. Turn on the receiver and adjust its sensitivity.
4. Move the receiver's probe along the suspected path of the wire. The receiver will emit an audible tone, strongest when directly over the wire.
5. For analog signals, the detection depth is up to 0.3 meters.

6.4 Prova di continuità

1. Connect the emitter to the cable or wire using the appropriate connector (RJ45, RJ11, or alligator clips).
2. Activate the continuity test function on the emitter.
3. Observe the continuity indicator lights on the emitter. If the resistance value is less than 1KΩ, continuity is confirmed, and the corresponding indicator lights will illuminate. An additional indicator light will operate for every 100Ω, and all lights will be on above 1KΩ.

6.5 Line Finding and Break Detection

The PM6819A can help locate specific lines and identify breaks.

• When tracing a cable, a sudden loss or significant decrease in signal strength from the receiver indicates a potential break in the line.
• The device's ability to detect signals through walls and underground makes it effective for locating hidden wiring.

Figura 5: Illustration of the PM6819A detecting a break in an underground cable. The receiver emits sound ('bibibi~') when a signal is present and no sound when the cable is broken.

Figura 6: The PM6819A's capability to find both underground cables and in-wall wiring, demonstrating its versatility.

7. Manutenzione

• Pulizia: Pulire il dispositivo con un panno asciutto e morbido. Non utilizzare detergenti abrasivi o solventi.
• Sostituzione della batteria: Replace the 9V battery in the receiver when the low voltage indicator flashes. Recharge the emitter's lithium battery as needed.
• Magazzinaggio: Store the device in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the 9V battery from the receiver.

8. Risoluzione Dei Problemi

• Nessun rilevamento del segnale:
  • Ensure both emitter and receiver are powered on.
  • Controllare i livelli della batteria in entrambe le unità.
  • Verificare che i collegamenti dei cavi siano saldi.
  • Increase receiver sensitivity.
  • Ensure the emitter is set to the correct signal mode (digital for RJ45/RJ11, analog for other wires).
• Segnale debole:
  • Adjust receiver sensitivity.
  • Ensure the cable is within the specified detection depth.
  • Environmental interference may affect signal strength; try to minimize external noise.
• Emitter Not Charging:
  • Controllare il cavo di ricarica e l'adattatore di alimentazione.
  • Assicurarsi che la porta di ricarica sia pulita e priva di detriti.

9. Garanzia e supporto

The Peakmeter PM6819A Multifunctional Wire Tracker comes with a garanzia di un anno dalla data di acquisto. La presente garanzia copre difetti di fabbricazione e malfunzionamenti in condizioni di normale utilizzo. Non copre danni causati da uso improprio, incidenti, modifiche non autorizzate o manutenzione impropria.

For technical support, warranty claims, or service inquiries, please contact your retailer or the manufacturer directly. Please have your purchase receipt and product model number (PM6819A) available when contacting support.