Bestway 58515-7 Sand Filter Pump Instruction Manual

1. Informazioni sulla sicurezza

WARNING! READ THE INSTRUCTION MANUAL CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.

Always ensure the pump is disconnected from the power supply before performing any maintenance or adjustments. Do not operate the pump if the power cord is damaged. Keep children away from the pump during operation. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

2. Prodotto finitoview

The Bestway 58515-7 Sand Filter Pump is designed for efficient filtration of above-ground pool water. It features a pump flow rate of 3,596 L/h and is compatible with pools ranging from 1,100 to 18,100 L. The durable, corrosion-resistant filter tank ensures long-lasting performance. It comes pre-assembled with a 360° rotatable flange clamp for simplified installation and includes a 6-position valve for various functions and a pre-filter basket to capture larger debris.

3. componenti

The Bestway 58515-7 Sand Filter Pump includes the following main components:

• Serbatoio filtro a sabbia
• Unità motore pompa
• 6-Position Control Valve
• Manometro
• Cestello prefiltro
• Tubi e Clamps
• Cavo di alimentazione

4. Impostazione

4.1 Preparing the Filter Tank

1. Ensure the drain plug at the bottom of the filter tank is securely closed.
2. Remove the 6-position control valve from the top of the filter tank.
3. Carefully add the appropriate filter media (pool filter sand or Bestway Polysphere filter balls) into the tank. Refer to the product specifications for the correct amount.

4.2 Collegamento della pompa

1. Place the pump on a solid, level surface, ensuring it is at least 2 meters (6.5 feet) away from the pool.
2. Connect the hoses from the pool's skimmer/return outlets to the pump's inlet and outlet ports using the provided clamps. The pump's inlet (suction) connects to the pool's skimmer, and the pump's outlet (return) connects to the pool's return jet.
3. Attach the 6-position control valve back onto the filter tank, ensuring a tight seal.
4. Assicurarsi che tutti i collegamenti siano ben saldi per evitare perdite.

5. Azionamento della pompa

5.1 6-Position Valve Functions

The multi-port valve allows for different operational modes:

5.2 Avviamento della pompa

1. Assicurarsi che la piscina sia riempita fino al livello appropriato e che tutti i tubi siano collegati.
2. Set the 6-position valve to the FILTRO posizione.
3. Collegare la pompa a una presa elettrica dotata di messa a terra.
4. Premere il pulsante di accensione per avviare la pompa.
5. Check the pressure gauge. If the pressure is too high, the filter media may need backwashing.

6. Manutenzione

6.1 Regular Cleaning (Backwash and Rinse)

Perform backwashing when the pressure gauge indicates high pressure (typically 0.2-0.3 bar above the starting pressure) or when water flow to the pool decreases significantly.

1. Spegnere la pompa e staccarla dalla presa.
2. Set the 6-position valve to the LAVAGGIO A CONTROLOVANZA posizione.
3. Plug in and turn on the pump. Run for approximately 2-3 minutes or until the water in the sight glass (if available) runs clear.
4. Spegnere la pompa e staccarla dalla presa.
5. Set the 6-position valve to the RISCIACQUO posizione.
6. Plug in and turn on the pump. Run for 30-60 seconds.
7. Spegnere la pompa e staccarla dalla presa.
8. Set the 6-position valve back to the FILTRO posizione.
9. Collegare e accendere la pompa per il normale funzionamento.

6.2 Pre-Filter Basket Cleaning

1. Spegnere la pompa e staccarla dalla presa.
2. Close the inlet and outlet valves to the pump.
3. Unscrew the pre-filter cover and remove the basket.
4. Clean any debris from the basket.
5. Reinsert the basket and securely close the cover.
6. Open the inlet and outlet valves and restart the pump.

7. Risoluzione Dei Problemi

8. Specifiche