Introduzione
This manual provides essential information for the proper setup, operation, and maintenance of the YELUFT AMG8833 IR 8x8 Infrared Thermal Imager Module. Please read this manual thoroughly before using the device to ensure optimal performance and safety.
Prodotto finitoview
The YELUFT AMG8833 is a compact 8x8 array infrared thermal imager sensor designed for integration with microcontrollers such as Raspberry Pi and Arduino. It provides 64 individual infrared temperature readings via an I2C interface, enabling applications like human detection and mini thermal imaging.
Figure 1: The AMG8833 module held between fingers, demonstrating its compact size.
Caratteristiche principali:
- 8x8 array of infrared heat sensors for 64 individual temperature readings.
- I2C communication interface for easy integration with microcontrollers.
- Configurable interrupt pin for threshold-based event triggering.
- Compact design suitable for various embedded projects.
Cosa è incluso:
- 1 x AMG8833 IR 8x8 Infrared Thermal Imager Module
- 1 x Manuale di istruzioni (questo documento)
Figura 2: Fronte e retro view of the AMG8833 module.
Specifiche
The following table details the technical specifications of the AMG8833 Infrared Thermal Imager Module:
| Parametro | Valore |
|---|---|
| Alimentazione elettrica | 3V - 5V |
| Precisione | ±2.5°C (±4.5°F) |
| Detection Range (Humans) | Fino a 7 metri (23 piedi) |
| Frequenza fotogrammi massima | 10 Hz |
| Campo di misurazione della temperatura | da 0°C a 80°C (da 32°F a 176°F) |
| Interfaccia | I2C |
| Peso dell'articolo | 9.98 grammi |
| Dimensioni del pacco | Dimensioni: 13 x 11.99 x 3 cm |
| Numero di modello | GY-AMG8833 |
Figure 3: Key operational parameters of the AMG8833 module.
Figure 4: Physical dimensions and weight of the AMG8833 module.
Impostazione e connessione
Alimentazione elettrica:
The AMG8833 module requires a power supply between 3V and 5V. Connect the power source to the Numero di telaio E Terra perni.
Comunicazione I2C:
The module communicates via the I2C protocol. Connect the SCL (Serial Clock) and SDA (Serial Data) pins to the corresponding I2C pins on your microcontroller (e.g., Raspberry Pi, Arduino, ESP8266).
Connessioni opzionali:
- INT (Interrupt): This pin can be configured to trigger an interrupt on your microcontroller when a pixel's temperature exceeds or falls below a set threshold.
- ADO (Address Select): This pin allows for selecting the I2C address, enabling the use of multiple AMG8833 modules on the same I2C bus.
Schema elettrico:
Refer to the following diagram for typical wiring connections:
Figure 5: Wiring diagram for the AMG8833 module.
Istruzioni per l'uso
Acquisizione dati:
Once connected, the module can be initialized and read using your microcontroller's I2C library. The sensor provides 64 individual temperature readings (an 8x8 array) which can be accessed sequentially.
Letture di temperatura:
The temperature measurement range is from 0°C to 80°C (32°F to 176°F) with an accuracy of ±2.5°C (±4.5°F). Each pixel's reading represents the infrared temperature of its corresponding area.
Frequenza dei fotogrammi:
The maximum frame rate for data acquisition is 10Hz, meaning you can obtain up to 10 full 8x8 temperature arrays per second.
Interrupt Functionality:
The configurable interrupt pin can be programmed to alert your microcontroller when specific temperature conditions are met, such as a sudden change in temperature or a temperature exceeding a predefined limit. This is useful for event-driven applications like motion or presence detection.
Manutenzione
The AMG8833 module is designed for low maintenance. To ensure longevity and accurate performance:
- Keep the sensor surface clean and free from dust or obstructions.
- Avoid exposing the module to extreme temperatures, humidity, or corrosive environments beyond its specified operating range.
- Handle the module with care to prevent physical damage to the sensor or PCB.
Risoluzione dei problemi
Nessun dato o letture errate:
- Controllare le connessioni: Verify all VIN, GND, SCL, and SDA connections are secure and correctly wired according to the diagram.
- Alimentazione elettrica: Ensure the power supply is within the 3V-5V range and stable.
- Indirizzo I2C: Confirm the correct I2C address is being used in your code. The default address is typically 0x68 or 0x69, depending on the ADO pin state.
- Compatibilità della libreria: Ensure you are using a compatible I2C library for your microcontroller and the AMG8833 sensor.
Sensore non rilevato:
- I2C Scanner: Use an I2C scanner sketch (available for Arduino) or tool (for Raspberry Pi) to confirm the module is detected on the I2C bus and identify its address.
- Cablaggio: Double-check SCL and SDA lines for shorts or open circuits.
Garanzia e supporto
For warranty information and technical support, please refer to the seller's policies or contact YELUFT customer service through the platform where the product was purchased. Keep your purchase receipt for warranty claims.