Manuale di istruzioni per la chiave universale wireless XHORSE XN

Introduzione

The XHORSE XN Wireless Universal Remote Key is designed for use with Xhorse VVDI tools, including the VVDI2 Mini Remote Programmer and VVDI Key Tool. These universal remote keys provide a versatile solution for generating and matching car keys, offering both wireless and wired connection methods for programming. Each key is manufactured with quality assurance and is compatible with a wide range of vehicle systems.

Installazione e assemblaggio

This section outlines the steps for assembling and preparing your XHORSE XN Wireless Universal Remote Key for use.

1. Disassembling the Remote Key

To access the internal components for battery installation or chip placement, the remote key needs to be disassembled. There are typically three methods for opening the key shell:

1. **Using a Matching Tool:** Insert a matching tool into the right side of the key and push up until the back cover pops out.
2. **Using a Pry Tool:** Locate the small gap on the back of the remote key. Use a suitable pry tool to gently separate the back shell.
3. **Manual Separation:** Firmly pull both sides of the remote key apart with your hands. Continue to disassemble the shell to reveal the internal chip.

2. Battery and Key Blade Installation

After disassembling the key, you can install the necessary components:

• **Battery Installation:** Insert the appropriate battery (CR2032, not included) into the designated slot on the circuit board. Ensure correct polarity.
• **Key Blade Installation:** If your remote key requires a physical key blade (uncut key blade needs additional purchase), install it into the key shell as shown in the diagram.

Istruzioni per l'uso

The XHORSE XN Wireless Universal Remote Key is designed to be programmed using Xhorse VVDI tools. The general process involves generating the remote and then matching it to your vehicle.

1. Generating the Remote Key

Use your VVDI Key Tool or VVDI2 Mini Remote Programmer to generate the remote key. This process typically involves selecting the correct vehicle type and remote key type within the software. The video demonstrates connecting the remote key to the VVDI Mini Key Tool for generation.

• **Wireless Connection:** Place the remote key into the VVDI tool's detection area.
• **Wired Connection:** Connect the remote key's circuit board to the VVDI tool using the provided cable.

Follow the on-screen instructions on your VVDI tool to complete the remote generation process.

2. Key Matching to Vehicle

After generating the remote, it must be matched to your vehicle. This step usually requires connecting your VVDI tool to the vehicle's OBD-II port and following the specific matching procedures for your car's make and model. Refer to your VVDI tool's manual for detailed vehicle-specific matching instructions.

The Q&A content indicates that the key is usable for Universal, Wireless applications, reinforcing its broad compatibility.

Manutenzione

Proper maintenance ensures the longevity and reliable performance of your XHORSE XN Wireless Universal Remote Key.

Sostituzione della batteria

The remote key uses a CR2032 battery (not included). If the remote's range decreases or it stops responding, the battery may need replacement. Follow the key disassembly steps outlined in the "Setup and Assembly" section to access the battery compartment. Replace the old battery with a new CR2032 battery, ensuring correct polarity, then reassemble the key.

Assistenza generale

• Tenere la chiave telecomando asciutta e lontana dall'umidità.
• Avoid dropping the key or subjecting it to strong impacts.
• Pulire l'esterno con un panno morbido e asciutto. Non utilizzare prodotti chimici aggressivi.
• Store the key in a safe place to prevent damage.

Risoluzione dei problemi

If you encounter issues with your XHORSE XN Wireless Universal Remote Key, try the following troubleshooting steps:

• **Remote Not Responding:**
  • Check the battery. Replace it if it's low or dead (CR2032).
  • Ensure the key is properly assembled and the circuit board is seated correctly.
  • Verify that the key has been correctly generated and matched to your vehicle using a VVDI tool.
• **Short Operating Range:**
  • Sostituire la batteria.
  • Ensure there are no strong electromagnetic interferences in the vicinity.
• **Difficulty Generating/Matching:**
  • Ensure your VVDI tool is updated to the latest software version.
  • Check all cable connections if using a wired method.
  • Refer to the specific instructions for your VVDI tool and vehicle model.

Specifiche

Specific Model Dimensions:

• **XNDS00EN (3 Buttons):** Product Size: 2.76 x 1.37 x 0.70 inches (approx.), Product Weight: 62g (approx.)
• **XNFO01EN (3 Buttons):** Product Size: 2.76 x 1.37 x 0.70 inches (approx.), Product Weight: 62g (approx.)
• **XNBU01EN (4 Buttons):** Product Size: 2.46 x 1.57 x 0.59 inches (approx.), Product Weight: 45g (approx.)
• Other models (XNHO00EN, XNHY02EN, XNAU01EN, XNTO00EN) have similar universal design and functionality.

Suggerimenti per l'utente

• These keys are universal and wireless, making them versatile for various applications with compatible VVDI tools.
• Remember that the battery (CR2032) and uncut key blade are not included and must be purchased separately.
• Always ensure your VVDI programming tool is updated to the latest firmware for optimal compatibility and functionality.

Garanzia e supporto

XHORSE products are manufactured to high standards and undergo quality control before leaving the factory. For specific warranty information, technical support, or service inquiries, please refer to the official Xhorse webo contattare il rivenditore autorizzato. Conservare la ricevuta d'acquisto come prova d'acquisto per eventuali reclami in garanzia.