Manuale utente dell'essiccatore a filamento SUNLU S2

1. Introduzione

The SUNLU S2 Filament Dryer Box is designed to dry 3D printer filaments, improving print quality by removing moisture. It features 360° surround heating, an internal fan for even temperature distribution, and an LED touch screen for easy operation and monitoring of temperature, humidity, and drying time.

2. Contenuto della confezione

Si prega di selezionare la casella per i seguenti elementi:

• 1 x SUNLU S2 Filament Dryer Box
• 1 x Power Adapter (EU, US, UK, or AU Plug depending on region)
• 1 x Direction Manual (this document)
• 1 x Certificazione
• 1 x Date Tag
• 1 x Spugna

Immagine: rappresentazione visiva degli articoli inclusi nella confezione.

3. Prodotto finitoview e Caratteristiche

The S2 Filament Dryer Box is engineered with advanced features to ensure optimal filament drying:

• Ventola interna: A fan located at the bottom blows upwards, creating a thermal cycle for uniform temperature distribution and efficient moisture expulsion.
• 360° Surround Heating: Utilizes upper and lower double heating plates for rapid and even heating from top to bottom, drying filaments efficiently.
• Ampio intervallo di temperatura: Adjustable temperature from 35℃ to 70℃, suitable for drying various filament types including PA and PC.
• Schermo tattile LED: An extra-large 4.6-inch (3.42*2.87 inch) LCD touch screen displays real-time temperature, humidity, selected filament type, and countdown time. It supports switching between Celsius and Fahrenheit.
• Dual Temperature Probes: Ensures accurate temperature detection for precise control.
• LED Marquee Light: Indicates the real-time working status. The speed of accumulation reflects the temperature difference between measured and set values.
• Controllo intelligente: Features intelligent presets for multiple filament types and drying modes, reducing the need for manual settings after initial configuration.
• Filament Hole: Designed to allow printing while drying, with a hole for filament to pass through and for moisture to be discharged.

Immagine: Frontale view of the S2 Dryer Box highlighting key features like internal fan, heating, and display.

Image: Exploded diagram illustrating the internal fan and heating elements.

Image: Display showing temperature units can be switched between °C and °F.

Image: Detail of the filament output hole for printing during drying.

4. Impostazione

1. Disimballare: Rimuovere con attenzione tutti i componenti dalla confezione.
2. Posizionamento: Place the S2 Filament Dryer Box on a stable, flat surface away from direct sunlight, heat sources, and excessive humidity.
3. Collegamento elettrico: Connect the provided power adapter to the dryer box and then plug it into a suitable power outlet (AC 100V~240V, 50/60Hz).
4. Carica filamento: Open the lid of the dryer box. Place your filament spool inside. The maximum coil size supported is φ210mm x 85mm (H). Close the lid securely.
5. Filament Path (Optional, for printing while drying): If you intend to print while drying, feed the filament through the designated filament hole on the side of the dryer box to your 3D printer.

Image: Diagram illustrating the maximum filament spool size that fits inside the S2 Dryer Box.

5. Istruzioni per l'uso

1. Accensione: Once connected to power, the LED touch screen will light up.
2. Imposta temperatura: Use the touch screen controls to set the desired drying temperature. The range is 35℃ to 70℃. Refer to the "Reference Settings" table below for recommended temperatures based on filament type.
3. Impostare il tempo di asciugatura: Use the touch screen controls to set the drying duration. Recommended times are typically 3-6 hours, but can be extended if needed.
4. Seleziona il tipo di filamento: The S2 features intelligent presets. Select your filament type (e.g., PLA, ABS, PA) from the options on the screen. This helps the dryer optimize its settings.
5. Inizio asciugatura: Press the "RUN" button on the touch screen to begin the drying process. The LED marquee light will indicate operation.
6. Monitorare i progressi: The screen will display real-time humidity (RH%), current temperature (PV), set temperature (SV), and remaining countdown time.
7. Conversione unità di temperatura: You can switch between Celsius (°C) and Fahrenheit (°F) on the touch screen.

Reference Settings for Filament Drying

The following table provides recommended drying temperatures and times for common filament types. These are general guidelines and may vary based on filament brand and environmental conditions.

Suggerimenti:

• Before printing, it is recommended to bake first and then print; after baking, it is better to print while baking.
• When the ambient temperature is too low and the drying oven does not heat up to the set value, it is recommended to extend the baking time for more than 1 hour.
• This table serves as a reference for drying time and temperature of commonly used consumables.

Image: Detailed reference table for filament drying settings.

Understanding the Drying Process

During the initial heating stage (0-15 minutes), humidity is removed from the filament, causing the relative humidity inside the box to rise to approximately 50%. During the subsequent moisture evaporation stage (around 120 minutes), the relative humidity drops to about 25% as moisture is expelled.

Video: Demonstration of the S2 drying oven's performance, showing real-time humidity changes during the drying process.

6. Manutenzione

• Pulizia: Ensure the dryer box is unplugged and cooled before cleaning. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.
• Magazzinaggio: When not in use, store the dryer box in a cool, dry place.
• Conservazione del filamento: For best results, store filaments in a sealed container with desiccant after drying and when not in use.

7. Risoluzione Dei Problemi

• Filament still wet after drying:
  • Ensure the correct temperature and time settings are used for the filament type.
  • If ambient temperature is too low, extend drying time by more than 1 hour.
  • If filament has excessive moisture or environment is very humid, open the box briefly to release accumulated moisture, then quickly close to continue drying. This can reduce overall drying time.
• Schermo non funzionante:
  • Verificare che l'adattatore di alimentazione sia collegato correttamente e che la presa di corrente funzioni.
• Poor print quality (e.g., popping sounds, bubbles):
  • This often indicates wet filament. Increase drying time or temperature as per the reference table.
  • Consider drying the filament immediately before or during printing.

Image: Visual comparison of a 3D print made with wet filament (left, showing popping sound artifacts) versus dry filament (right, printing normally).

8. Specifiche

Image: Product dimensions and environmental specifications.

Image: Detailed power adapter specifications.

9. Suggerimenti per l'utente

• Capacità: The drying oven has a capacity for one standard filament spool.
• Compatibilità del filamento: The dryer supports consumable wire diameters of 1.75mm, 2.85mm, and 3.00mm.
• Produttore: The S2 Filament Dryer is manufactured by SUNLU Company, which is a direct factory with ISO9001, SGS, and TUV certifications.

10. Garanzia e supporto

SUNLU is a direct factory and provides pre-sales and after-sales service for its products. For any issues or inquiries, please feel free to contact SUNLU customer support.

If you encounter any problems with the goods, please contact us for assistance with refunds or replacements.

Image: SUNLU certifications and quality assurance.