1. Introduzione
This manual provides detailed instructions for the installation, operation, and maintenance of your DDPAI Dashcam Hardwire Kit. This kit is designed to provide continuous power to your compatible DDPAI dashcam, enabling 24-hour parking monitoring functionality. Please read this manual thoroughly before installation and use.
Compatible Dashcam Models: DDPAI Z60, DDPAI Z60 Pro, DDPAI MINI2X, DDPAI Z50 Pro, DDPAI A400.
2. Configurazione e installazione
Proper installation of the hardwire kit is crucial for safe and reliable operation of the 24-hour parking monitoring feature. It involves connecting to your vehicle's electrical system. If you are unsure about any steps, it is recommended to seek professional assistance.
2.1 Componenti Oltreview
- DDPAI Hardwire Kit (main unit with Type-C connector)
- Yellow wire (BAT+): For constant power
- Red wire (ACC): For ignition-switched power
- Black wire (GND): For ground connection
- Fuse taps (included with yellow and red wires)
2.2 Schema elettrico e collegamenti
Follow the wiring diagram carefully to connect the hardwire kit to your vehicle's fuse box.
- Identificare la scatola dei fusibili: Locate your vehicle's fuse box, typically found under the dashboard, in the engine bay, or in the trunk. Consult your vehicle's owner's manual for its exact location.
- Connect Ground (GND): Connect the black wire (GND) to a metal bolt or screw on the vehicle's chassis that provides a good ground connection. Ensure the connection is secure and free from paint or rust.
- Connect Constant Power (BAT+): Use the yellow wire (BAT+) with the provided fuse tap. Identify a fuse in your vehicle's fuse box that provides constant power (always on, even when the ignition is off). This is essential for 24-hour parking monitoring. Insert the original fuse into the lower slot of the fuse tap, and then insert the fuse tap into the chosen fuse slot.
- Connect Ignition-Switched Power (ACC): Use the red wire (ACC) with the provided fuse tap. Identify a fuse in your vehicle's fuse box that provides power only when the ignition is on (e.g., radio, cigarette lighter). Insert the original fuse into the lower slot of the fuse tap, and then insert the fuse tap into the chosen fuse slot.
- Connettiti alla Dashcam: Plug the Type-C connector of the hardwire kit into the power input port of your DDPAI dashcam.
- Gestione dei cavi: Route the cables neatly and securely, tucking them behind trim panels to avoid interference with driving and to maintain a clean appearance.
Avvertimento: Incorrect wiring can damage your vehicle's electrical system or the dashcam. Always ensure correct polarity and fuse selection. If you are not confident, consult a qualified auto electrician.
3. Istruzioni per l'uso
Once the hardwire kit is correctly installed and connected to your DDPAI dashcam, the dashcam will automatically utilize the hardwire kit for power. The primary function enabled by this kit is 24-hour parking monitoring.
- Modalità di parcheggio automatico: When your vehicle's ignition is turned off, the dashcam will detect the loss of ACC power and automatically switch to parking monitoring mode, drawing power from the constant power (BAT+) connection.
- Exiting Parking Mode: When the vehicle's ignition is turned on, the dashcam will detect the ACC power and automatically switch back to normal recording mode.
- Impostazioni della dashcam: Refer to your specific DDPAI dashcam's user manual for detailed instructions on configuring parking mode settings, such as motion detection sensitivity or time-lapse recording, if available.
4. Manutenzione
The DDPAI Hardwire Kit is designed for durability and requires minimal maintenance. However, following these guidelines can help ensure its longevity and optimal performance:
- Ispezione regolare: Periodically check all connections (fuse taps, ground, and Type-C connector) to ensure they are secure and free from corrosion or damage.
- Integrità del cavo: Ensure that all cables are not pinched, frayed, or exposed to excessive heat or moisture.
- Pulizia: Keep the hardwire kit unit and connections clean and free from dust or debris.
- Condizioni ambientali: Avoid exposing the hardwire kit to extreme temperatures or direct water contact.
5. Risoluzione Dei Problemi
If you encounter issues with your DDPAI Hardwire Kit, refer to the following troubleshooting steps:
| Problema | Possibile causa | Soluzione |
|---|---|---|
| La dashcam non si accende. | Collegamento allentato, fusibile bruciato, cablaggio errato. | Check all wiring connections. Verify fuses in the fuse box and fuse taps are intact. Ensure correct BAT+ and ACC connections. |
| 24-hour parking monitoring not working. | Incorrect BAT+ connection, dashcam settings. | Ensure the yellow BAT+ wire is connected to a constant power source. Check your dashcam's settings to ensure parking mode is enabled and configured correctly. |
| Dashcam drains car battery. | Basso volumetage cut-off not configured or faulty. | The DDPAI Hardwire Kit includes a low-voltage protection feature. If battery drain occurs, ensure the kit is functioning correctly. Consult your dashcam's manual for any adjustable low-voltage cut-off settings. |
| Intermittent power to dashcam. | Loose connections, faulty fuse tap. | Secure all connections. Replace fuse taps if they appear damaged or are not making good contact. |
If the problem persists after following these steps, please contact DDPAI customer support or a qualified technician.
6. Specifiche
| Caratteristica | Specificazione |
|---|---|
| Ingresso volumetage | CC 12V-24V |
| Volume di uscitatage | CC 5V |
| Corrente di uscita | 2.4A |
| Lunghezza del cavo | 3.5 metri |
| Tipo di connettore | Tipo C |
| Peso | 0.15 kg |
| Certificazioni | Certificazione CE, FCC, RoHS |
| Compatible Dashcams | DDPAI Z60, Z60 Pro, MINI2X, Z50 Pro, A400 |
7. Suggerimenti per l'utente
- Selezione del fusibile: When choosing fuse slots for BAT+ and ACC, select circuits that are not critical to vehicle operation (e.g., avoid airbags, engine control). A good choice for BAT+ might be a constant power outlet, and for ACC, the radio or cigarette lighter.
- Connessioni di prova: Before reassembling your vehicle's interior, test the hardwire kit and dashcam to ensure parking mode activates and deactivates correctly with the ignition.
- Instradamento dei cavi: Use cable clips or zip ties to secure excess cable length and prevent it from interfering with pedals or other vehicle controls.
8. Garanzia e supporto
For warranty information, please refer to the terms and conditions provided at the time of purchase or contact your retailer. DDPAI provides customer support for product-related inquiries and technical assistance.
Contatta l'assistenza: Please visit the official DDPAI websito o contatta il tuo punto vendita per le informazioni di supporto più aggiornate.
