1. Introduzione
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Philips HF-R 258 TL-D EII Electronic Ballast. This electronic ballast is designed for use with 58 Watt TL-D fluorescent lamps, operating on 220-240V, 50/60Hz electrical systems.
Si prega di leggere attentamente il presente manuale prima dell'installazione e di conservarlo per riferimento futuro.
2. Informazioni sulla sicurezza
Osservare sempre le seguenti precauzioni di sicurezza:
- Rischio elettrico: Installation and maintenance should only be performed by a qualified electrician. Ensure power is disconnected at the circuit breaker before any installation or servicing.
- Voltage Compatibilità: Verificare che il volume di fornituratage (220-240V, 50/60Hz) matches the ballast's requirements.
- Messa a terra corretta: Ensure the ballast is properly grounded to prevent electrical shock.
- Lamp Compatibilità: Use only with compatible 58 Watt TL-D fluorescent lamps.
- Condizioni ambientali: Do not expose the ballast to excessive moisture or extreme temperatures.
3. Installazione e configurazione
The Philips HF-R 258 TL-D EII electronic ballast is designed for easy integration into lighting fixtures. Follow the steps below for proper installation.
3.1. Schema elettrico
Refer to the following diagram for correct electrical connections. Ensure all connections are secure and comply with local electrical codes.
Figura 3.1: Wiring diagram for the Philips HF-R 258 TL-D EII electronic ballast. This diagram illustrates the connections for the DC input (terminals 13, 14), AC input (terminals 8, 9), ground (terminal 10), and the lamp connections (terminals 1-7) for two TL-D lamps.
3.2. MCB Compatibility
The number of ballasts that can be connected to a Miniature Circuit Breaker (MCB) depends on the MCB type and rating. Consult the table below for guidance.
Figura 3.2: MCB compatibility table. This table provides information on the maximum number of ballasts relative to different MCB types (B, C, L, I, G, U, II, K, III) and their respective ratings (10A, 16A).
| Tipo MCB | Valutazione | Rating Relative Number of Ballasts |
|---|---|---|
| B | 16A | 100% |
| B | 10A | 63% |
| C | 16A | 170% |
| C | 10A | 104% |
| L, io | 16A | 108% |
| L, io | 10A | 65% |
| G, U, II | 16A | 212% |
| G, U, II | 10A | 127% |
| K, III | 16A | 254% |
| K, III | 10A | 154% |
4. Istruzioni per l'uso
Once properly installed, the Philips HF-R 258 TL-D EII electronic ballast operates automatically to power compatible fluorescent lamps.
- Accensione: Apply power to the circuit. The ballast will initiate the lamps.
- Funzione di attenuazione: This ballast supports 1-10V dimming. Connect a compatible 1-10V dimmer to the designated dimming terminals (DC input terminals 13 and 14 as shown in the wiring diagram) to control the light output.
- Avvio immediato: Electronic ballasts provide instant, flicker-free starting for fluorescent lamps.
5. Manutenzione
The Philips HF-R 258 TL-D EII electronic ballast is designed for long-term, maintenance-free operation. However, general care and proper disposal are important.
- Pulizia: If cleaning is necessary, disconnect power and wipe the ballast with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Lamp Sostituzione: Quando si sostituisce lamps, ensure power is off. Replace with compatible 58 Watt TL-D fluorescent lamps.
- Riciclaggio: Electronic ballasts and fluorescent lamps contain materials that should be recycled responsibly. Consult local regulations for proper disposal and recycling procedures.
For more information on recycling and cleaning, please refer to the manufacturer's guidelines or local waste management services.
6. Risoluzione Dei Problemi
If you experience issues with your Philips HF-R 258 TL-D EII electronic ballast, consider the following common problems and solutions:
- Lamps Not Lighting:
- Controllare l'alimentazione elettrica dell'alimentatore.
- Verificare che la lamps are correctly installed and are not faulty.
- Controllare che tutti i collegamenti dei cavi non siano allentati o danneggiati.
- Sfarfallio Lamps:
- Assicurare lamps are fully seated in their sockets.
- Controllare il volume correttotage fornitura.
- Lamps may be at the end of their lifespan and require replacement.
- La funzione di attenuazione non funziona:
- Verify the 1-10V dimmer is compatible and correctly wired to the ballast's dimming terminals.
- Check the dimmer's power supply and functionality.
If problems persist, contact a qualified electrician or Philips Lighting customer support.
7. Specifiche
Key technical specifications for the Philips HF-R 258 TL-D EII Electronic Ballast:
| Attributo | Valore |
|---|---|
| Marca | Illuminazione Philips |
| Produttore | Philips |
| Numero di modello | 91019630 |
| Dimensioni del prodotto (L x P x A) | Dimensioni: 36 x 3 x 2.2 cm |
| Peso dell'articolo | 299 grammi |
| Numero di articoli | 1 |
| Stile | Moderno |
| Colore | Bianco |
| Forma | Tubolare (T) |
| Voltage | 230 Volt |
| Usi specifici | Tecnologia di illuminazione |
| Caratteristiche speciali | Dimmable (1-10V) |
| Tipo di spina | Cavo elettrico |
| Batterie incluse/richieste | NO |
| Compatibile Lamp Tipo | Fluorescent (TL-D) |
| Compatibile Lamp Cosatage | 58 Watt (come da titolo del prodotto) |
| Etichetta energetica | 13 |
| Durata media della vita | 50000 ore |
Note: Some specifications in the source data, such as "Puissance: 90 Watts" and conflicting bulb base types (GX5.3, E27), appear to be generic or refer to other products. This ballast is specifically designed for 58 Watt TL-D lamps.
8. Garanzia e supporto
Warranty information for your Philips HF-R 258 TL-D EII electronic ballast is typically provided at the point of purchase or with the product packaging. Please retain your proof of purchase for warranty claims.
For technical support, service, or further inquiries, please contact Philips Lighting customer service or visit their official website. Contact details can usually be found on the product packaging or the manufacturer's websito.
