1. Prodotto finitoview
The Cherub WST-520GB is an automatic tuner designed for guitars and basses. It features a clear display, LED indicators for tuning status, and multiple input options for accurate instrument tuning, making it suitable for both electric and acoustic instruments.
2. Contenuto della confezione
- Cherub WST-520GB Tuner
- 2 batterie AAA
- Manuale dell'utente (questo documento)
3. Caratteristiche principali
- Automatic tuning method for ease of use.
- Built-in microphone for tuning acoustic instruments.
- 1/4-inch input jack for connecting electric instruments.
- LED indicators clearly show flat, in-tune, and sharp status.
- Supports chromatic tuning mode for versatile instrument compatibility.
4. Controlli e indicatori
Figura 1: Cherub WST-520GB Tuner Front Panel
- Schermo di visualizzazione: Features a needle-style meter indicating pitch deviation from -50 (flat) to +50 (sharp) cents.
- Indicatori LED: Three lights above the display. The left red LED indicates flat, the right red LED indicates sharp, and the center green LED indicates in-tune.
- MICROFONO: Integrated microphone for detecting the sound of acoustic instruments.
- ITEM / FLAT Button: Used to cycle through instrument modes (e.g., Guitar, Bass, Chromatic) and to activate or adjust flat tuning settings.
- ON---CALIB / OFF Button: Powers the unit on or off. May also be used for calibration functions.
- Presa INGRESSO: A 1/4-inch (6.35mm) jack for connecting electric instruments directly.
- Uscita jack: A 1/4-inch (6.35mm) jack for passing the instrument's signal through to an amplifier o altre apparecchiature audio.
5. Impostazione
5.1. Installazione della batteria
The Cherub WST-520GB operates on two AAA batteries. Locate the battery compartment on the back of the unit. Open the cover, insert the batteries ensuring correct polarity (+/-) as marked, and then securely close the cover.
5.2. Collegamento dello strumento
For Electric Instruments: Connect a standard 1/4-inch instrument cable from your instrument's output jack to the INGRESSO jack on the tuner. If you wish to send the tuned signal to an amplifier, connect another 1/4-inch cable from the tuner's PRODUZIONE jack per il tuo ampcontributo del lificatore.
For Acoustic Instruments: No cable connection is required. The tuner's built-in microphone will detect the sound of your instrument.
6. Istruzioni per l'uso
6.1. Accensione/Spegnimento
Premere e tenere premuto il tasto ON---CALIB / OFF button for approximately 2 seconds to power the tuner on or off.
6.2. Selezione della modalità di sintonizzazione
After powering on, the tuner will display its current mode. Press the ITEM / FLAT button repeatedly to cycle through the available instrument modes, such as Guitar, Bass, or Chromatic. Select the mode appropriate for your instrument.
6.3. Accordare lo strumento
- Play a single note on your instrument. Ensure the note sustains long enough for the tuner to detect it.
- Observe the display and LED indicators:
- If the left red LED illuminates and the needle points to the left (towards -50), the note is flat.
- If the right red LED illuminates and the needle points to the right (towards +50), the note is sharp.
- If the green LED illuminates and the needle is centered (at 0), the note is in tune.
- Adjust your instrument's tuning pegs until the green LED illuminates and the needle is precisely centered on the display.
6.4. Using the Flat Function
If you need to tune your instrument to a lower pitch (e.g., half-step down), press the ITEM / FLAT button briefly after selecting your instrument mode. The display will indicate the activated flat setting (e.g., 'b' for one half-step flat). Press again to cycle through flat settings or return to standard tuning.
7. Manutenzione
- Pulizia: Use a soft, dry cloth to clean the tuner's exterior. Avoid using abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or internal components.
- Sostituzione della batteria: Replace the AAA batteries when the display dims, the LEDs become faint, or the unit fails to power on. If the tuner will not be used for an extended period, remove the batteries to prevent potential leakage and damage.
- Magazzinaggio: Store the tuner in a dry environment, away from extreme temperatures, high humidity, and direct sunlight. Protect it from physical shocks or drops.
8. Risoluzione Dei Problemi
8.1. Tuner does not power on.
- Check battery installation. Ensure batteries are inserted with correct polarity.
- Replace batteries with fresh ones, as they may be depleted.
8.2. Tuner is not detecting sound.
- For electric instruments: Ensure the instrument cable is securely connected to the INGRESSO jack. Verify that the cable and instrument are functioning correctly. Increase the instrument's volume output.
- For acoustic instruments: Ensure the instrument is played loudly enough for the built-in microphone (MIC) to detect the sound. Try moving the tuner closer to the sound source.
8.3. Tuning seems inaccurate.
- Verify that the correct instrument mode (Guitar, Bass, Chromatic) is selected.
- Minimize ambient noise that might interfere with the microphone's detection.
- If using the input jack, ensure the cable connection is stable and free from interference.
9. Specifiche
- Modello: WST-520GB
- Modalità di sintonizzazione: Chromatic, Guitar, Bass
- Ingresso: 1/4-inch (6.35mm) mono jack
- Produzione: 1/4-inch (6.35mm) mono jack
- Energia: Batterie 2 x AAA (incluse)
- Dimensioni: 4.1 x 3.7 x 1 pollici (10.4 x 9.4 x 2.5 cm)
- Peso: 3.2 once (90.7 grammi)
- Materiale: Plastica
10. Garanzia e supporto
For detailed warranty information, technical assistance, or customer support, please refer to the manufacturer's official webo contattare direttamente il servizio clienti. Si consiglia di conservare la ricevuta d'acquisto come prova d'acquisto per eventuali reclami in garanzia.
