1. Introduzione
This instruction manual provides essential information for the proper installation, maintenance, and troubleshooting of the Candy 92130871 washing machine replacement belt. Please read this manual thoroughly before attempting any installation or repair to ensure safe and effective operation.
2. Informazioni sulla sicurezza
- Always disconnect the washing machine from the power supply before attempting any installation, maintenance, or repair work. Failure to do so can result in electric shock or serious injury.
- Per evitare lesioni, indossare adeguati dispositivi di protezione individuale, come i guanti.
- In caso di dubbi su qualche passaggio, consultare un tecnico qualificato.
- Tenere bambini e animali domestici lontani dall'apparecchio durante la riparazione.
- Assicurarsi che tutti gli utensili siano in buone condizioni e utilizzati correttamente.
3. Prodotto finitoview
The Candy 92130871 is an authentic replacement drive belt designed for various Candy washing machine models. This belt is crucial for transmitting power from the motor to the drum, enabling the washing machine to operate correctly.
Image 1: The Candy 92130871 washing machine replacement belt. This image shows the black rubber belt, typically ribbed on one side for grip.
4. Compatibilità
This replacement belt (Manufacturer Code: 92130871) is compatible with a wide range of Candy washing machine models. Please verify your washing machine's model number against the list below to ensure proper fitment.
I modelli compatibili includono:
- CANDY AC16, ACTIVA50, ACTIVA51, ACTIVA60, ACTIVA61, ACTIVA64SLIM, ACTIVA66SL, ACTIVA6CI
- ALISE060, ALISE065, ALISE066, ALISE'160XT, ALISE190X, ALISE6190X0, ALISE'.610B, ALISE'65 ARG, ALISE'650, ALISE'696
- AQUAV.6, AQUAVIVA60, AQUAVIVA63, AQUAVIVA650, AQUAVIVA66
- C36ZXT, C532, C535T, C536T, C55XT (I), C564XT plata, C577T, C588XT, C58XT (I), C6077T, XT AQUAM, CM.608XT (I)
- C616XT (I), C625XT, C634XT, C634XT (CE), C634XT (NORD), C636XT, C647XT (I), C657XT (I)
- CB52T, CB52TCKD, CB53XTR, CB612XT, CB613TR, CB623XTTR HC, CB62T, CB62TR, CB633XTR, CB634XT, CB63TES, CB63TR, CB63TRCKD, CB63XTR
- CE520T, CE530, CE615, CE621T, CE623R, CE625TR, CE629T, CE637XT, CE650TR
- CG5444T, CG5544T, CG623T, CG644.3T, CG644T, CG654XT, CGAQ665XT
- CH630, CHIARA51XT, CHIARA540XTR, CHIARA552TR, CHIARA55XTR, CHIARA5XT, CHIARA5XTV, CHIARA642XTR, CHIARA65XTR, CHIARA65XT, CHIARA65XTV, CHIARA65XTR, CHIARA65X2XTR, CHIARA6XT
- CI50XTR, CI537T, CI57TR, CI589XT, CI60XTR, CI60XTR H/C, CI620TP, CI622T, CI624T, CI626XT, CI627T, CI637T, CI648XT, CI658XT
- CJ6514, CJ543T, CJ613XT, CJ643T, CJA52T
- CL66XT, CN50T, CN50T-04S, CN60T, CN63T, CN63T CI, CN63TCKD, CN63TRU-03S
- IPC 610, CR61, CS47XT (I), CSB640XTR, CSE640XTR, CSE615XT, CM.SE635XT, CSG624T, CSI615T, CSI635XTR, CSI635XTRSY, CSN62T, CSN62T-03S
- EXCL.S641XTR, EXCLUS.60, EXCLUS.6000, EXCLUS540XTR, EXCLUS65XTR
- HOL165XTR, HOL62, VACANZAS 6, HOLIDAY161, HOLIDAY60, HOLIDAY603, HOLIDAY61
- ICL60T, LADYC.623CKD, SEL.S643XTR, SELEC 0.631 XTR, SELECTA600, SELECTA60X, SELECTA61XXTR
- SL5000EXC, SL50EXCLUS., SLIM644AQUAV, SLIMMY508XT, SLIMMY634XT, SLIMMY655XT, SLIMMY6AQUAV, SLIMMYCB62XT, WM601.
5. Installazione (configurazione)
Replacing a washing machine drive belt requires careful attention. Follow these general steps. Specific machine designs may vary, so refer to your washing machine's primary service manual if available.
- Preparazione:
- Scollegare la lavatrice dall'alimentazione principale.
- Chiudere l'alimentazione idrica alla macchina.
- Pull the washing machine away from the wall to access the rear panel.
- Accedi alla Cintura:
- Locate and remove the screws securing the rear access panel of the washing machine.
- Carefully remove the panel to expose the motor, drum pulley, and the old belt (if still present).
- Rimuovere la vecchia cinghia:
- If the old belt is still partially attached, carefully pry it off the motor pulley and then the larger drum pulley. Note its orientation.
- Installare la nuova cinghia:
- First, loop the new Candy 92130871 belt around the smaller motor pulley.
- Successivamente, avvolgere parzialmente la cinghia attorno alla puleggia del tamburo più grande.
- While holding the belt firmly on the motor pulley and partially on the drum pulley, slowly rotate the drum pulley by hand. The belt should gradually roll onto the drum pulley until it is fully seated. Ensure the ribbed side of the belt (if applicable) faces the pulleys correctly.
- Check that the belt is centered on both pulleys and has proper tension. It should be snug but allow for a small amount of flex.
- Rimontare:
- Replace the rear access panel and secure it with the screws.
- Push the washing machine back into its position.
- Reconnect the power supply and water supply.
- Test:
- Run a short, empty wash cycle to ensure the belt operates smoothly and quietly.
6. Manutenzione
Regular inspection of the drive belt can help prevent future issues and extend the life of your washing machine.
- Ispezione periodica: Ogni 1-2 anni, o se si notano rumori insoliti o problemi di prestazioni, ispezionare la cinghia per verificare la presenza di segni di usura, crepe, sfilacciamenti o allungamenti.
- Tensione corretta: Ensure the belt maintains proper tension. A loose belt can slip, causing the drum to not spin or spin intermittently. An overly tight belt can put undue stress on the motor and drum bearings.
- Pulizia: Keep the area around the motor and pulleys free from lint, debris, and moisture, which can affect belt performance and lifespan.
7. Risoluzione Dei Problemi
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Il tamburo non gira o gira lentamente | Broken, stretched, or slipped drive belt. | Inspect the belt. Replace if broken or severely worn. Re-seat if slipped. |
| Forte rumore stridente o stridente durante il ciclo di centrifuga | Worn or misaligned drive belt. | Check belt for wear and proper alignment on pulleys. Replace if worn. |
| Odore di bruciato | Belt slipping due to improper tension or excessive load. | Check belt tension and ensure it's not overloaded. Replace if damaged from slipping. |
Se le procedure di risoluzione dei problemi non risolvono il problema, si consiglia di contattare un tecnico qualificato.
8. Specifiche
- Marca: Caramella
- Numero modello: 92130871
- Tipo di prodotto: Washing Machine Replacement Belt
- Dispositivi compatibili: Lavatrice
- Dimensioni della confezione: 30 x 20 x 3 cm (circa)
- Peso del prodotto: 100 grammi (circa)
9. Garanzia e supporto
For information regarding warranty coverage, technical support, or to purchase additional parts, please refer to the official Candy websito o contattare il servizio clienti. Conservare la ricevuta d'acquisto come prova d'acquisto.
Caramelle ufficiali Websito: www.candy-group.com
