Electrolux 134792700 Heater Installation and Maintenance Manual

Introduzione

This manual provides detailed instructions for the safe and effective installation, operation, and maintenance of your Electrolux 134792700 Heater. Please read all instructions carefully before beginning any procedures.

The Electrolux 134792700 Heater is an OEM replacement part designed for specific dryer models. It operates at 5500 watts and is silver in color, weighing approximately 2.91 pounds.

Informazioni sulla sicurezza

• Always disconnect power to the appliance before performing any service or maintenance.
• Indossare dispositivi di protezione individuale adeguati, come guanti e protezioni per gli occhi.
• In caso di dubbi su qualche passaggio, consultare un tecnico qualificato.
• Tenere tutti i componenti e gli utensili fuori dalla portata dei bambini.

Configurazione e installazione

This section outlines the steps for replacing the heating element in your dryer. It is recommended to follow these steps carefully.

Strumenti necessari:

• Cacciavite con testa a croce
• Wrench (for ground wire)
• Marker (optional, for labeling wires)

Fasi di installazione:

1. Scollegare l'alimentazione: Unplug the dryer from the electrical outlet. Ensure the power is completely off before proceeding.
   

   Image: Dryer power cord being unplugged from the wall outlet.
2. Rimuovere il pannello superiore: Locate and remove the two screws at the upper back of the dryer. Slide the top panel off.

   Video: A 360 gradi view of the Electrolux 134792700 Heater, showing its cylindrical shape, heating coils, and electrical connections. This video provides a detailed look at the component being installed.

3. Remove Control Panel: Remove the two additional screws located on the sides of the control panel, near the top. Gently lift and prop the control panel out of the way.
4. Rimuovere il pannello frontale: Locate and remove the four screws securing the front panel. Two are typically at the top corners, and two are at the bottom corners.
5. Disconnect Door Light: Carefully disconnect the door light assembly from the front panel. This usually involves pushing it in, rotating, and pulling it out.
6. Disconnect Wires from Heating Element: Label the wires (top, middle, bottom) connected to the heating element for easy reassembly. Disconnect all wires by pushing the two parts together and pulling. Loosen the ground wire with a wrench.
7. Remove Old Heating Element: Unscrew the long screw holding the heating element in place. Carefully pull the old heating element out of its housing. Note the condition of the old coils.
8. Install New Heating Element: Place the new Electrolux 134792700 Heater into the housing. Secure it with the long screw. Reconnect the wires according to your labels (top, middle, bottom) and tighten the ground wire.
9. Rimontare l'asciugatrice: Reattach the lint trap housing, reconnect the door light, reattach the front panel, secure the control panel, and finally, slide the top panel back into place and secure its screws.
10. Esecuzione del test: Plug the dryer back into the electrical outlet. Open the dryer door to confirm the interior light turns on. Close the door and start a short cycle to ensure the dryer heats up and operates correctly.

Istruzioni per l'uso

After successful installation, operate your dryer according to its original manufacturer's instructions. Ensure the lint trap is clean before each use for optimal performance and safety.

Manutenzione

• Lint Trap Cleaning: Clean the lint trap before or after every load to maintain drying efficiency and prevent fire hazards.
• Pulizia dello sfiato: Periodically inspect and clean the dryer vent system to ensure proper airflow. Blocked vents can lead to longer drying times and potential overheating.
• Ispezione dei componenti: Annually inspect the heating element and other internal components for signs of wear or damage.

Risoluzione dei problemi

If your dryer displays an E64 error code, this typically indicates a "Heater Open Circuit" or a "Heating Element or Wiring Defective" issue. Replacing the heating element, as described in the installation section, is the primary solution for this error.

Problemi comuni e soluzioni:

• Asciugatrice non riscalda: Check the heating element for visible damage or continuity with a multimeter. Ensure all electrical connections are secure.
• Tempi di asciugatura lunghi: Clean the lint trap and dryer vent thoroughly. Overloading the dryer can also cause this.
• Codice di errore E64: This indicates a heating element or wiring defect. Replace the heating element following the instructions in the Setup section.

Specifiche

Informazioni sulla garanzia

Specific warranty details for the Electrolux 134792700 Heater are not provided in this manual. Please refer to the product packaging or contact Electrolux customer service for warranty information.

Assistenza clienti

For further assistance or technical support regarding your Electrolux 134792700 Heater, please contact Electrolux customer service. Contact information can typically be found on the official Electrolux webdocumentazione del sito o del prodotto.

If you receive a damaged product or encounter any problems during use, please contact the seller directly for assistance. They typically respond within 24 hours.