Avidsen 100108 Wireless GSM Alarm Kit

1. Introduzione

The Avidsen 100108 Wireless GSM Alarm Kit is designed to provide security for your home or office. This kit includes a central unit with an integrated siren and presence sensor, a door/window magnetic contact, and two remote controls. Its GSM functionality allows for remote activation and alerts via SMS and calls.

Please read this manual carefully before installation and operation to ensure proper use and maximum security.

2. Contenuto della confezione

Verificare che tutti i componenti siano presenti nella confezione:

• 1x Central Unit: Includes call function, siren, and presence (motion) sensor.
• 1x Door/Window Opening Sensor: Magnetic contact for entry points.
• 2x Remote Controls: Per attivare e disattivare il sistema.
• 3x CR2 Batteries: Required for operation (included).

Image: Avidsen 100108 Wireless GSM Alarm Kit showing the central unit, remote controls, and a sensor.

3. Impostazione

3.1. Installazione della batteria

1. Unità Centrale: Open the battery compartment on the back of the central unit. Insert the 3 CR2 Lithium batteries, ensuring correct polarity (+/-). Close the compartment securely.
2. Sensore porta/finestra: Aprire il sensore casing and insert the required battery (refer to the sensor's specific markings for type and polarity).
3. Telecomandi: Remote controls typically come with pre-installed batteries or require small button-cell batteries. Check the remote for a battery tab to remove or a compartment to open.

3.2. SIM Card Installation (for GSM Functionality)

The central unit requires a 2G GSM SIM card (not included) to enable SMS and call alerts. Ensure the SIM card is active and has sufficient credit if it's a prepaid card.

1. Locate the SIM card slot on the central unit.
2. Inserire la scheda SIM nello slot, assicurandosi che sia orientata correttamente.
3. Power on the central unit. The unit will attempt to register with the GSM network.

3.3. Posizionamento dei componenti

• Unità Centrale: Place the central unit in a central location within your protected area, away from direct sunlight and heat sources. Ensure it has good GSM signal reception.
• Sensore porta/finestra: Mount the magnetic contact on a door or window frame. Align the two parts (sensor and magnet) so they are no more than 1 cm apart when the door/window is closed.
• Presence Sensor (PIR): The central unit has an integrated PIR sensor. Position the unit to cover the desired detection area, typically a main hallway or room entrance. Avoid pointing it directly at heat sources or windows where sunlight or drafts might cause false alarms.

3.4. Pairing Remote Controls and Sensors

The remote controls and sensors are typically pre-paired with the central unit. If re-pairing is necessary or if adding new accessories, refer to the detailed pairing instructions in the full product manual (not provided here). Generally, this involves putting the central unit into a 'learning' mode and then activating the accessory.

4. Istruzioni per l'uso

4.1. Attivazione del sistema

To arm the alarm system, press the Braccio button on your remote control. The central unit will emit a confirmation sound, and an indicator light may illuminate, signifying that the system is armed. All connected sensors are now active.

4.2. Disattivazione del sistema

To disarm the alarm system, press the Disarmare button on your remote control. The central unit will emit a different confirmation sound, and the indicator light will turn off, indicating the system is disarmed.

4.3. Pulsante antipanico

In caso di emergenza premere il tasto Panico button (often depicted as a bell or lightning bolt) on your remote control. This will immediately trigger the siren and initiate GSM alerts (calls/SMS) to pre-programmed numbers, regardless of the system's armed status.

4.4. GSM Alert Functionality

When an alarm is triggered (e.g., by a motion sensor or door opening sensor), the central unit will:

• Activate the integrated siren.
• Send an SMS alert to pre-programmed phone numbers.
• Initiate a call to pre-programmed phone numbers.

To program alert numbers, refer to the detailed instructions in the full product manual. This typically involves sending specific SMS commands to the alarm unit's SIM card number from an authorized phone.

5. Manutenzione

5.1. Sostituzione della batteria

Regularly check the battery status of the central unit and all wireless sensors. Low battery indicators (audible alerts or flashing lights) will signal when batteries need replacement. Always replace with the specified battery type (e.g., CR2 for the central unit) and ensure correct polarity.

5.2. Pulizia

Clean the central unit and sensors periodically with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the device's surface or internal components. Keep sensors free from dust and obstructions to ensure optimal performance.

5.3. Test di sistema

It is recommended to test the alarm system periodically (e.g., monthly) to ensure all components are functioning correctly. This includes testing sensors, remote controls, siren, and GSM alert functionality.

6. Risoluzione Dei Problemi

7. Specifiche

• Marca: Avidisen
• Numero modello: 100108
• Fonte di energia: Batteria
• Batterie: 3 CR2 (Lithium), included
• Materiale: Plastica
• Tecnologia di connettività: Senza fili
• Tipo di avviso: Audio e movimento
• Metodo di controllo: Telecomando
• Peso del prodotto: 340 grammi
• Tipo di montaggio: Door (for magnetic contact)
• Dispositivi compatibili: Smartphone (for GSM alerts)

8. Garanzia e supporto

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Avidsen websito. Conservare la prova d'acquisto per eventuali reclami in garanzia.

If you encounter issues not covered in this manual, please contact Avidsen customer service for assistance.