1. Introduzione
The Hormann Fit 1 BS is a wireless in-wall remote control designed for convenient operation of compatible Hormann garage door openers and radio receivers. This device transmits signals at 868 MHz, supporting both BiSecur and standard 868 MHz frequencies. It is intended for indoor use in dry environments.
This manual provides essential information for the safe and effective installation, setup, and use of your Hormann Fit 1 BS remote control. Please read these instructions carefully before beginning installation or operation.
2. Istruzioni di sicurezza
- Sicurezza generale: This device is for indoor use only. Do not expose it to moisture, extreme temperatures, or direct sunlight.
- Sicurezza della batteria: Use only the specified battery type (2 x 1.5 V LR03/AAA). Ensure correct polarity when inserting batteries. Do not mix old and new batteries, or different types of batteries. Dispose of used batteries responsibly according to local regulations.
- Installazione: Ensure the installation location is stable and free from obstructions. Do not install near heat sources or in areas with high vibration.
- Bambini: Tenere il dispositivo e i suoi componenti fuori dalla portata dei bambini.
- Riparazioni: Non tentare di riparare o modificare il dispositivo autonomamente. Per qualsiasi intervento di assistenza, rivolgersi a personale qualificato.
3. Contenuto della confezione
Verificare che tutti gli articoli siano presenti nel pacco:
- 1 x Hormann Fit 1 BS Wireless In-Wall Remote Control (868 MHz BiSecur)
- 1 x Manuale utente (questo documento)
- 2 x 1.5 V LR03/AAA Batteries (may be pre-installed or included separately)
4. Installation and Battery Insertion
4.1. Inserimento della batteria
- Carefully open the back cover of the remote control.
- Insert two 1.5 V LR03/AAA batteries, ensuring correct polarity (+/-).
- Chiudere saldamente il coperchio posteriore.
4.2. Mounting the Remote Control
The Fit 1 BS is designed for in-wall mounting. Choose a suitable indoor location within range of your garage door opener or receiver. The device can be mounted directly onto a wall surface.
- Segnare sulla parete la posizione di montaggio desiderata.
- Secure the remote control's back plate to the wall using appropriate screws (not included) for your wall type.
- Snap the front part of the remote control onto the secured back plate.
Figure 1: Hormann Fit 1 BS In-Wall Remote Control. This image shows the compact design of the remote control, suitable for discreet wall mounting.
5. Operating: Pairing with a Receiver
To operate your garage door opener or radio receiver, the Fit 1 BS remote control must first be paired with it. The exact pairing procedure may vary slightly depending on your specific Hormann receiver model. Always refer to the instruction manual of your garage door opener or receiver for detailed pairing steps.
A general pairing procedure is as follows:
- Activate Learning Mode on Receiver: On your Hormann garage door opener or radio receiver, locate the 'Learn' or 'Program' button. Press and hold this button until the indicator light (usually an LED) starts flashing or illuminates steadily, indicating it is in learning mode.
- Trasmetti segnale da remoto: Within the active learning mode window (typically a few seconds to a minute), press the button on your Fit 1 BS remote control.
- Conferma associazione: The indicator light on your receiver should change its behavior (e.g., flash rapidly, turn off, or illuminate steadily) to confirm successful pairing.
- Operazione di prova: Press the button on the Fit 1 BS remote control again to test if it now operates the connected device.
If pairing is unsuccessful, repeat the steps. Ensure the remote control is within close proximity to the receiver during the pairing process.
6. Manutenzione
6.1. Sostituzione della batteria
When the remote control's range decreases or it stops responding, the batteries may need replacement. Follow the steps in Section 4.1 to replace the two 1.5 V LR03/AAA batteries. Always replace both batteries at the same time with new ones of the same type.
6.2. Pulizia
Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners, solvents, or wet cloths, as these can damage the device.
7. Risoluzione Dei Problemi
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Il telecomando non aziona il dispositivo. | Le batterie sono scariche o esaurite. | Sostituire le batterie (vedere Sezione 6.1). |
| Remote control is not paired with the receiver. | Perform the pairing procedure (see Section 5). | |
| Fuori dal limite. | Move closer to the receiver. Ensure no large metal objects are obstructing the signal path. | |
| Autonomia operativa ridotta. | Batterie scariche. | Sostituire le batterie (vedere Sezione 6.1). |
| Interference from other radio devices. | Try operating from a different location or check for other 868 MHz devices nearby. |
If the problem persists after attempting these solutions, please contact Hormann customer support.
8. Specifiche
- Modello: FIT 1 BS
- Marca: Hormann
- Frequenza: 868 MHz BiSecur / 868 MHz
- Canali: 1
- Tipo di protezione: For dry rooms only
- Intervallo di temperatura: Da -20 ° C a +60 ° C (da -4 ° F a +140 ° F)
- Batterie: 2 x 1.5 V LR03/AAA
- Colore: Bianco puro (RAL 9010)
- Dimensioni (L x A x P): 80 x 80 x 15 mm (3.15 x 3.15 x 0.59 pollici)
- Tecnologia di connettività: Frequenza Radio
- Portata massima: 50 metri (circa 164 piedi)
- Dispositivi compatibili: Hormann garage door openers and radio receivers (BiSecur or 868 MHz)
9. Garanzia e supporto
For information regarding warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Hormann website. If you encounter any issues that cannot be resolved using the troubleshooting guide, or require technical assistance, please contact Hormann customer support.
Please have your product model number (FIT 1 BS) and purchase details ready when contacting support.
