KeylessOption Telecomando per auto con accesso senza chiave e chiave sostitutiva per LHJ011 Manuale di istruzioni

Introduzione

This manual provides detailed instructions for the KeylessOption Keyless Entry Remote Car Key Fob and Key Replacement, model LHJ011. It covers product overview, setup, programming, maintenance, and specifications to ensure proper use and functionality.

Prodotto finitoview

The KeylessOption LHJ011 is a replacement keyless entry remote and key designed to function identically to your vehicle's original equipment. It includes a fully tested remote with a pre-installed battery and an uncut key blade.

Immagine: Frontale view of two KeylessOption LHJ011 key fobs, each featuring lock and unlock buttons, a red panic button, and an attached uncut key blade. These units are designed for keyless entry and vehicle ignition.

Immagine: Indietro view of two KeylessOption LHJ011 key fobs, showing the smooth, black plastic casing and the key ring attachment point. This view highlights the compact design of the remote units.

Setup and Key Cutting

Before programming the remote functions, the included key blade must be cut to match your vehicle's original key. This process is typically performed by a professional locksmith or an automotive dealership.

1. Taglio chiave: Take the new key fob and your original vehicle key to a qualified locksmith or dealership. They will cut the new key blade to match your existing key. This is essential for starting the vehicle.
2. Installazione della batteria: The remote comes with a CR2032 battery pre-installed. If replacement is needed, refer to the maintenance section.

Operating Instructions: Remote Programming

The KeylessOption LHJ011 remote control functions (lock, unlock, panic) are self-programmable for many compatible vehicles. Follow these step-by-step instructions carefully. It is recommended to program all new and existing remotes in a single session.

General Programming Procedure (Example for GM Vehicles, verify specific vehicle instructions):

1. Preparazione: Gather all key fobs (new and existing) you wish to program. Ensure all vehicle doors are closed.
2. Entra in modalità di programmazione:
   • Sit in the driver's seat.
   • Tieni premuto il tasto SBLOCCARE button on the driver's side door panel.
   • While holding the UNLOCK button, insert your newly cut key into the ignition.
   • Cycle the ignition to the ON position (do not start the engine), then immediately to SPENTO, quindi torna a ON, e poi a SPENTO Ancora.
   • Release the UNLOCK button on the door panel. The vehicle's door locks should cycle (lock and unlock) to confirm that the vehicle is now in programming mode.
3. Program Remote(s):
   • Take the first remote you wish to program (e.g., for Driver 1).
   • Premere e tenere premuto contemporaneamente il tasto SERRATURA E SBLOCCARE pulsanti sul telecomando.
   • Continue holding these buttons until the vehicle's door locks cycle again (this may take 15 to 30 seconds, or up to 100 seconds). This confirms the remote has been programmed.
   • If you have additional remotes (e.g., for Driver 2), immediately repeat the previous step for each remaining remote. Do not exit programming mode between remotes.
4. Uscire dalla modalità di programmazione:
   • Once all remotes are programmed, turn the ignition key to the ON position, then to SPENTO.
   • Open the driver's door. This action typically exits the programming mode.
5. Test Remotes: Test all programmed remotes to ensure they function correctly (lock, unlock, panic). The first remote programmed will typically be assigned to Driver 1, and subsequent remotes to Driver 2, if your vehicle supports this feature.

Nota: Specific programming procedures may vary slightly by vehicle make and model. Always refer to your vehicle's owner's manual or the manufacturer's recommended programming instructions if these steps do not work.

Manutenzione

Sostituzione della batteria

The KeylessOption LHJ011 remote uses one CR2032 coin cell battery. When the remote's range decreases or it stops responding, the battery may need replacement.

1. Open the Fob Casing: Aprire con cautela il coperchio del telecomandoasing. There is usually a small notch on the side where you can insert a flat-head screwdriver or a coin to gently separate the two halves.
2. Rimuovere la vecchia batteria: Note the orientation (+/-) of the existing CR2032 battery. Gently remove it.
3. Inserire una nuova batteria: Insert a new CR2032 battery with the positive (+) side facing the same direction as the old battery.
4. Chiudi Casing: Align the two halves of the fob casing e premerli saldamente insieme finché non scattano saldamente in posizione.
5. Funzionalità di prova: Test the remote's functions (lock, unlock) to ensure the new battery is working correctly.

Nota: Smaltire le vecchie batterie in modo responsabile secondo le normative locali.

Risoluzione dei problemi

Specifiche

• Modello: LHJ011
• Marca: Opzione senza chiave
• Numero di parte del produttore: KPT4037
• Numeri di parte OEM: 15132198, 15186200, 15186201, 15186203, 15186209, 21997127, 22730827, LHJ011, 10377295, 15132197
• Tipo di batteria: 1 x CR2032 (incluso)
• Materiale: Plastica
• Dimensioni del prodotto: Circa 4"L x 2"W
• Peso dell'articolo: Circa 1.58 once
• Tipo di adattamento automobilistico: Adattamento specifico del veicolo
• Numero di pulsanti: 2 (Lock, Unlock) + Panic

Garanzia e supporto

Each KeylessOption product includes a warranty card. For specific warranty details, please refer to the included card or contact KeylessOption customer support. Technical support is available with each purchase to assist with programming or operational questions.

For further assistance, please visit the official KeylessOption store or contact their customer service department.

KeylessOption Store: Visita il negozio