Manuali+

Hormann HSE4 868 BS

Hormann HSE4 868 BS BiSecur 4-Channel Remote Control User Manual

Model: HSE4 868 BS | Brand: Hormann

1. Prodotto finitoview

The Hormann HSE4 868 BS BiSecur remote control is a 4-channel handheld transmitter designed for operating up to four different Hormann drives or functions. It features a modern design with a black textured plastic surface and chrome-plated die-cast zinc caps. This remote control is equipped with BiSecur technology, ensuring secure transmission, and is also backward compatible with older Hormann drives operating at 868.3 MHz (Series 1, 2, and 3, provided a Hormann 868 MHz receiver is present for Series 1).

Le caratteristiche principali includono:

  • 4 canali: Control up to four distinct functions or devices.
  • BiSecur Technology: High-quality, secure signal transmission.
  • Compatibilità con le versioni precedenti: Works with older Hormann 868.3 MHz transmitters (e.g., HS1/HS2/HS4 868, HSE2 868, HSM2/HSM4 868, HSP4/HSP4-C 868, HSD2-C/HSD2-A 868, HSZ1/HSZ2 868).
  • Programmazione facile: Simple remote programming procedure, no special equipment required.
  • Include: Battery (3V lithium button cell, type CR 2032) and a keyring for convenience.
  • Allineare: Up to 100 meters (actual range may vary depending on local conditions).
Hormann HSE4 868 BS BiSecur 4-Channel Remote Control, black matte finish with four buttons and a keyring.

Figure 1: Hormann HSE4 868 BS BiSecur Remote Control.

2. Configurazione e programmazione

This section outlines the general procedure for programming your new Hormann HSE4 868 BS BiSecur remote control. The remote features a self-learning function for easy setup.

2.1. Pairing with a BiSecur Receiver (Newer Systems)

  1. Preparare il ricevitore: Locate the programming button on your Hormann drive's receiver unit. The exact location may vary by model (refer to your drive's manual).
  2. Attiva la modalità di apprendimento: Press and hold the programming button on the receiver until the LED indicator on the receiver starts flashing (usually red). This indicates the receiver is in learning mode.
  3. Transmit Signal from New Remote: Take your new HSE4 868 BS remote control. Press and hold the desired button on the new remote that you wish to program.
  4. Conferma associazione: Keep the button on the new remote pressed. The LED on the receiver should change its flashing pattern or illuminate steadily to confirm successful pairing. Release the button on the remote.
  5. Funzionalità di prova: Press the programmed button on your new remote to test if the drive responds correctly.

2.2. Copying from an Existing BiSecur Remote (Transmitter-to-Transmitter)

You can also copy the code from an existing, working BiSecur remote control to your new HSE4 868 BS remote.

  1. Posizione Telecomandi: Place the existing (master) remote and the new HSE4 868 BS remote close to each other, ideally touching or within a few centimeters.
  2. Activate Learning Mode on New Remote: Press and hold the button on the new HSE4 868 BS remote that you wish to program. The LED on the new remote will flash slowly.
  3. Transmit Code from Master Remote: While still holding the button on the new remote, press and hold the corresponding button on the existing (master) remote.
  4. Conferma copia: The LED on the new remote will flash faster, then illuminate steadily to indicate successful code transfer. Release both buttons.
  5. Funzionalità di prova: Test the newly programmed button on your HSE4 868 BS remote with your drive.

Nota: For older Hormann drives (Series 1, 2, 3) operating at 868.3 MHz (with blue buttons on older remotes), the HSE4 868 BS can be switched to a fixed code mode if necessary. Refer to the specific instructions for your drive model if you encounter compatibility issues.

3. Istruzioni per l'uso

The Hormann HSE4 868 BS remote control features four distinct buttons, allowing you to control up to four different functions or devices.

  • Funzioni dei pulsanti: Each of the four buttons can be programmed independently to operate a specific garage door, gate, or other compatible Hormann device.
  • Impulse Function: Pressing a programmed button will send an impulse signal to the receiver, typically initiating an open/stop/close cycle for a garage door or gate.
  • Indicatore LED: A small LED on the remote will illuminate briefly when a button is pressed, indicating that a signal is being transmitted. If the LED does not light up or is dim, the battery may need replacement.

Ensure you are within the operational range (up to 100 meters, depending on environmental factors) of your receiver for reliable operation.

4. Manutenzione

Una corretta manutenzione garantisce la longevità e l'affidabilità del vostro telecomando.

4.1. Sostituzione della batteria

The remote control is powered by a 3V lithium button cell battery, type CR 2032.

  1. Identificare il vano batteria: The battery compartment is typically located on the back or side of the remote. You may need a small screwdriver or coin to open it.
  2. Rimuovere la vecchia batteria: Carefully remove the old CR 2032 battery. Note its polarity (+/-).
  3. Inserire una nuova batteria: Insert a new CR 2032 battery, ensuring the correct polarity.
  4. Chiudi scomparto: Chiudere saldamente il vano batteria.
  5. Test: Provare il telecomando per assicurarsi che funzioni correttamente.

Disposizione: Smaltire le batterie usate secondo le normative locali. Non smaltire le batterie tra i rifiuti domestici.

4.2. Pulizia e conservazione

  • Pulire il telecomando con un panno morbido e asciutto. Non utilizzare detergenti abrasivi o solventi.
  • The remote is designed for dry environments only. Avoid exposure to moisture, rain, or extreme temperatures (-20°C to +60°C).
  • Store the remote in a safe place where it will not be accidentally activated or damaged.

5. Risoluzione Dei Problemi

If your Hormann HSE4 868 BS remote control is not functioning as expected, refer to the following troubleshooting tips:

Problema Possibile causa Soluzione
Remote does not operate the drive.
  • La batteria è scarica o scarica.
  • Il telecomando non è programmato.
  • Fuori dal limite.
  • Interferenza.
  • Sostituire la batteria CR 2032.
  • Seguire i passaggi di programmazione nella Sezione 2.
  • Avvicinatevi al ricevitore.
  • Check for sources of radio interference (e.g., other wireless devices).
Il LED sul telecomando non si accende.
  • La batteria è scarica o non è inserita correttamente.
  • Replace the CR 2032 battery, ensuring correct polarity.
La portata del telecomando è scarsa.
  • Batteria scarica.
  • Environmental interference (e.g., metal structures, walls).
  • Antenna on receiver is obstructed or damaged.
  • Sostituire la batteria.
  • Prova a operare da una posizione diversa.
  • Check the receiver's antenna. Consider an external antenna for extended range if needed (e.g., Hormann aerial).
Remote does not work with older 868.3 MHz drive.
  • Compatibility issue or fixed code mode required.
  • Ensure your drive has an 868 MHz receiver. Some older drives may require the remote to be switched to a fixed code mode. Consult your drive's manual for specific instructions on fixed code programming.

6. Specifiche tecniche

Numero di modello TR-424
Frequenza 868.3 MHz (BiSecur)
Canali 4
Codifica BiSecur, self-learning, fixed code possible for 868 MHz
Tipo di batteria 3V Lithium Button Cell, CR 2032
Dimensioni (L x A x P) Dimensioni: 28 mm x 70 mm x 14 mm
Tipo di protezione For dry rooms only
Intervallo di temperatura da -20°C a +60°C
Allineare Approx. 30-100 meters (depending on local conditions)
Produttore Hormann
Paese di origine Germania

7. Garanzia e supporto

Specific warranty information for the Hormann HSE4 868 BS BiSecur remote control is not provided in the product details. For warranty claims, technical support, or further assistance, please contact your Hormann dealer or the point of purchase. Keep your proof of purchase for any warranty-related inquiries.

Information regarding spare parts availability is also not explicitly provided. For spare parts, please contact Hormann customer service or an authorized dealer.