1. Introduzione
This manual provides detailed instructions for the safe and effective operation of your Sealey BT2014 Digital Battery and Alternator Tester with Printer. This device is designed for diagnosing battery and alternator faults, offering the convenience of printing test results directly. It is capable of testing battery condition with as little as 1.5V residual charge and analyzing the vehicle's charging system both at rest and under load.
Si prega di leggere attentamente questo manuale prima dell'uso e di conservarlo per riferimento futuro.
2. Informazioni sulla sicurezza
Always observe the following safety precautions to prevent personal injury and damage to the tester or vehicle.
- Quando si lavora in prossimità delle batterie dei veicoli, indossare protezioni per gli occhi e indumenti protettivi adeguati.
- Assicurarsi che il veicolo si trovi in un'area ben ventilata per disperdere eventuali gas della batteria.
- Tenere scintille, fiamme e materiali fumanti lontani dalla batteria.
- Avoid touching battery terminals or cables with bare hands.
- Non utilizzare il tester se appare danneggiato.
- Ensure correct polarity when connecting the tester to the battery (red clamp a positivo, nero clamp a negativo).
- Keep the tester dry and clean.
3. Contenuto della confezione
Upon opening your Sealey BT2014 package, please verify that all components are present and undamaged:
- Sealey BT2014 Digital Battery and Alternator Tester with integrated printer.
- Heavy-duty carry-case.
- Batteries (pre-installed or included for printer operation).
- Two rolls of printing paper.
- Manuale di istruzioni (il presente documento).
Figura 3.1: The Sealey BT2014 Digital Battery and Alternator Tester shown within its protective carry case, with all accessories visible.
4. Prodotto finitoview
The Sealey BT2014 is a robust diagnostic tool designed for automotive electrical system analysis. It features a clear digital display, intuitive controls, and an integrated thermal printer for immediate result documentation.
Figura 4.1: Davanti view of the Sealey BT2014 tester, displaying the screen, control buttons, and attached battery clamps.
4.1. componenti
- Display digitale: Mostra i risultati dei test e le opzioni del menu.
- Pulsanti di controllo: 'Forward', 'Back', 'Enter', 'Start/Stop' for navigation and operation.
- Integrated Printer: For printing test reports.
- Batteria Clamps: Rosso per positivo (+), nero per negativo (-).
- Printer Paper Compartment: Located under the clear cover.
Figura 4.2: Un dettagliato view of the Sealey BT2014 tester, highlighting the digital display and a printed test report emerging from the integrated printer.
5. Impostazione
5.1. Caricamento della carta per stampante
- Gently open the clear cover of the printer compartment.
- Insert a new roll of thermal paper, ensuring the paper feeds from the bottom of the roll.
- Pull a small length of paper out and close the cover, ensuring the paper exits through the slot.
5.2. Connecting to the Vehicle Battery
- Ensure the vehicle ignition is off and all accessories are disconnected.
- Collegare il rosso positivo (+) clamp al terminale positivo della batteria.
- Collegare il nero negativo (-) clamp al polo negativo della batteria.
- Ensure connections are secure and free from corrosion. The tester will power on automatically.
6. Istruzioni per l'uso
The BT2014 offers various testing modes accessible via the main menu.
6.1. Prova della batteria
This function assesses the health and charge level of the vehicle's battery.
- From the main menu, select 'Battery Test' using the 'Forward'/'Back' buttons and press 'Enter'.
- Follow the on-screen prompts to input battery type (e.g., Flooded, AGM, Gel) and Cold Cranking Amps (CCA) rating. This information is usually found on the battery label.
- The tester will perform the analysis. Once complete, the results will be displayed, showing voltage, CCA, state of health, and state of charge.
- You will be prompted to 'Print Result?'. Select 'Yes' or 'No' and press 'Enter'.
Figura 6.1: The Sealey BT2014 tester actively performing a test on a vehicle battery, with the display showing a prompt to print results.
6.2. Alternator Test (Charging System Test)
This function evaluates the vehicle's charging system, including the alternator's performance.
- From the main menu, select 'Alternator Test' and press 'Enter'.
- The tester will guide you through a series of steps, which typically include:
- Starting the vehicle engine.
- Running the engine at idle.
- Incrementoasing engine RPM to a specified level (e.g., 2000 RPM).
- Turning on electrical loads (e.g., headlights, fan).
- The tester will analyze the voltage output under various conditions.
- Results will be displayed, indicating the alternator's condition (e.g., 'Good', 'Low Output', 'High Output').
- You will be prompted to 'Print Result?'. Select 'Yes' or 'No' and press 'Enter'.
7. Manutenzione
7.1. Pulizia
Pulisci il tester con un panno morbido eamp cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
7.2. Printer Paper Replacement
When the printer runs out of paper, follow the steps in Section 5.1 to replace the roll. Use only thermal paper compatible with the BT2014.
7.3. Conservazione
Store the tester in its protective carry-case in a dry, cool environment, away from direct sunlight and extreme temperatures. Disconnect the battery clamps before storage.
Figura 7.1: The Sealey BT2014 tester securely stored within its closed, protective carry case, ready for transport or long-term storage.
8. Risoluzione Dei Problemi
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Il tester non si accende. | Poor battery connection; Vehicle battery completely dead. | Controllare clamp connections; Ensure battery has at least 1.5V residual charge. |
| La stampante non stampa. | Carta assente; Carta inserita in modo errato; Malfunzionamento della stampante. | Replace paper roll; Re-insert paper correctly; Contact support if issue persists. |
| Risultati dei test imprecisi. | Incorrect battery type/CCA input; Poor clamp connection; Corroded terminals. | Verify battery information; Clean battery terminals and ensure secure connections. |
9. Specifiche
| Caratteristica | Specificazione |
|---|---|
| Numero di modello | Modello BT2014 |
| Marca | Marea |
| Tipo di misurazione | Multimetro |
| Dimensioni del prodotto (L x P x A) | 17 x 82 x 17 millimetri |
| Peso dell'articolo | 1566 grammi |
| Fonte di alimentazione | AC (for charging/powering, specific details not provided) |
| Volume minimo della batteriatage for Test | 1.5V residual charge |
10. Garanzia e supporto
The Sealey BT2014 Digital Battery and Alternator Tester is covered by a Garanzia di 1 anni from the date of purchase. This guarantee covers manufacturing defects under normal use. Please retain your proof of purchase for warranty claims. Terms and conditions apply.
Figura 10.1: Official Sealey 1 Year Guarantee emblem, indicating product warranty coverage.
For technical support, warranty inquiries, or to order replacement parts (such as printer paper rolls), please contact your authorized Sealey dealer or visit the official Sealey websito per le informazioni di contatto.
