SIIG HDMI IP Extender Transmitter (CE-H23B11-S1) User Manual

Introduzione

This manual provides detailed instructions for the installation, operation, and maintenance of the SIIG HDMI IP Extender Transmitter (Model CE-H23B11-S1). This device is designed to transmit HDMI signals with stereo audio over a UTP CAT5e/6 cable up to 120 meters (394 feet). It supports HDbit-T protocol with H.264 compression, enabling a scalable matrix configuration over a dedicated IP network.

Contenuto della confezione

Verify that all items listed below are included in your package. If any items are missing or damaged, please contact your vendor for assistance.

• 1x SIIG HDMI IP Extender Transmitter (CE-H23B11-S1)
• 1x adattatore di alimentazione (CC 5 V)
• 1x cavo IR Blaster
• Cavo di ricezione 1x IR
• 1x RS-232 Terminal Block
• 2 staffe di montaggio con viti
• 1x Manuale utente

Image: Contents of the SIIG HDMI IP Extender Transmitter package.

Image: Various accessories for the SIIG HDMI IP Extender system, including power adapters, IR cables, remote, and mounting brackets.

Caratteristiche del prodotto

• Extends HDMI signals with stereo audio over a single UTP CAT5e/6 cable up to 120 meters (394 feet).
• Supports HDbit-T protocol with H.264 compression for efficient data transmission over IP.
• Scalable TX/RX Matrix configuration over a dedicated IP network, supporting up to 256 total units (maximum 100 transmitters).
• Supports video resolutions up to 1080p @60Hz.
• Features an HDMI local output (loop-out) on the transmitter for monitoring the source signal.
• Includes IR pass-back function for controlling the source device from the receiver location.
• Provides RS-232 pass-through for controlling RS-232 enabled devices.
• Compatible with computer control software for source selection and switching in Matrix mode.
• Robusto alloggiamento in metallo per una maggiore longevità.

Image: Front panel of the Transmitter unit, highlighting the IR sensor, power indicator, TX ID display, and reset button.

Configurazione e collegamenti

Follow these steps to set up your SIIG HDMI IP Extender Transmitter. A compatible receiver unit (Model CE-H23C11-S1) and a dedicated unmanaged IGMP Gigabit Switch are required for a complete system.

Identificazione dei componenti

Image: Front and rear panel port and indicator identification for the Transmitter.

• CC 5V: Jack di ingresso alimentazione.
• RJ45 USCITA: Connects to the network switch or directly to a receiver unit via CAT5e/6 cable.
• USCITA IR: Connects to the IR Blaster cable to control the source device.
• HDMI Local Output (Loop-Out): Connects to a local display for monitoring the HDMI source.
• Ingresso HDMI: Connects to the HDMI source device (e.g., Blu-ray player, PC).
• RS-232: Terminal block for RS-232 serial control.
• Sensore IR: Receives IR signals from a remote control (on the front panel).
• LED di potenza: Indica lo stato dell'alimentazione.
• ID TX: Digital display for Transmitter ID.
• Reset: Button to reset the unit.

Connection Steps (Point-to-Point)

1. Connect your HDMI source device (e.g., DVD player, PC) to the Ingresso HDMI porta dell'unità trasmettitore tramite un cavo HDMI.
2. (Optional) Connect a local display to the HDMI Local Output port of the Transmitter unit using an HDMI cable to monitor the source.
3. Collegare il USCITA RJ45 port of the Transmitter unit to the RJ45 IN port of a compatible SIIG HDMI IP Extender Receiver unit (sold separately) using a single CAT5e/6 Ethernet cable.
4. Collegare l'adattatore di alimentazione a CC 5V power jack of the Transmitter unit and plug it into an electrical outlet.
5. Ensure the Receiver unit is also powered on and connected to its display.

Matrix Connection (Many-to-Many)

For a matrix setup, multiple transmitters and receivers are connected via a dedicated unmanaged IGMP Gigabit Switch. This allows any source to be routed to any display.

Immagine: Example of a Many-to-Many Matrix Connection using an IGMP Switch.

1. Connect all HDMI source devices to their respective SIIG HDMI IP Extender Transmitter units via the Ingresso HDMI porti.
2. Collegare il USCITA RJ45 port of each Transmitter unit to an available port on a dedicated unmanaged IGMP Gigabit Switch using CAT5e/6 Ethernet cables.
3. Collegare il RJ45 IN port of each SIIG HDMI IP Extender Receiver unit (sold separately) to an available port on the same IGMP Gigabit Switch using CAT5e/6 Ethernet cables.
4. Connect each Receiver unit to its respective HDMI display via the Uscita HDMI porta.
5. Connect power adapters to all Transmitter and Receiver units and plug them into electrical outlets.
6. Importante: A dedicated unmanaged IGMP Gigabit Switch is highly recommended for optimal performance and reliability in matrix configurations. Ensure the switch supports IGMP functionality.

Istruzioni per l'uso

Accendere

After all connections are made, plug in the power adapters for both the Transmitter and Receiver units. The Power LED on the front panel of the Transmitter will illuminate.

TX ID Display

IL ID TX display on the front panel shows the identification number of the transmitter. In a matrix setup, each transmitter should have a unique ID for proper routing. Refer to the system's control software manual for configuring TX IDs.

IR Pass-Back Function

To control your HDMI source device from the remote display location:

1. Collegare il cavo del ricevitore IR al INFRAROSSO port on the Receiver unit (sold separately). Position the IR receiver eye to face your remote control.
2. Collegare il cavo IR Blaster al Uscita IR port on the Transmitter unit. Position the IR blaster emitter directly over the IR sensor of your HDMI source device.
3. You can now use your source device's remote control from the display location to send commands back to the source.

Passante RS-232

The RS-232 terminal block allows for serial control of RS-232 enabled devices. Connect your RS-232 control device to the terminal block on either the Transmitter or Receiver unit to extend control signals.

Software di controllo della matrice

For matrix configurations, SIIG provides computer control software to manage source selection and switching. Refer to the separate software manual for installation and operation instructions. This software allows you to route any transmitter's signal to any connected receiver.

Risoluzione dei problemi

• Nessuna immagine/segnale:
  • Assicurarsi che tutti i cavi HDMI ed Ethernet siano collegati saldamente.
  • Verify that both the Transmitter and Receiver units are powered on.
  • Check the HDMI source device and display for proper operation.
  • Test with shorter or different HDMI/Ethernet cables.
  • Ensure the Ethernet cable is CAT5e/6 and meets length requirements (max 120m).
  • In a matrix setup, confirm the IGMP Gigabit Switch is functioning correctly and supports IGMP.
  • Verify the TX ID on the transmitter matches the selected input on the receiver (if applicable).
• Scarsa qualità dell'immagine/sfarfallio:
  • Ensure the Ethernet cable is of high quality and properly terminated.
  • Se possibile, ridurre la lunghezza del cavo.
  • Check for electromagnetic interference (EMI) from other devices.
  • Verify that the resolution settings on the source device are compatible with the extender and display.
• Controllo IR non funzionante:
  • Ensure the IR Blaster is correctly positioned over the source device's IR sensor.
  • Ensure the IR Receiver is facing your remote control and connected to the Receiver unit.
  • Check for obstructions between the remote and the IR Receiver.
• RS-232 Control Issues:
  • Verify the RS-232 cable connections and pin assignments.
  • Ensure the baud rate and other serial communication settings match between the control device and the extender.

Specifiche

Image: Physical dimensions of the Transmitter unit.

Manutenzione

• Keep the device in a cool, dry, and well-ventilated area.
• Evitare di esporre l'unità alla luce solare diretta, a temperature elevate o all'umidità.
• Non smontare l'unità. Per qualsiasi intervento di manutenzione, rivolgersi a personale qualificato.
• Pulire l'unità con un panno morbido e asciutto. Non utilizzare detergenti liquidi o spray.
• Ensure proper cable management to prevent damage to cables and ports.

Garanzia

This SIIG product is covered by a Garanzia limitata di 2 anno from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, abuse, unauthorized modifications, or natural disasters. Please retain your proof of purchase for warranty claims.

Assistenza clienti

For technical support, product information, or warranty inquiries, please visit the official SIIG website or contact their customer service department. Contact information can typically be found on the product packaging or the SIIG websito.