Okin 2 Button 5 Pin Recliner Hand Control with USB - Instruction Manual

Introduzione

This manual provides instructions for the installation, operation, and maintenance of your Okin 2 Button 5 Pin Lift Chair or Power Recliner Hand Control with USB.

This control unit is designed for use with compatible lift chairs and power recliners, offering convenient control over reclining functions and a built-in USB charging port.

Caratteristiche del prodotto

• Materiale: Zinc alloy pane for durability.
• Ricarica USB: 5V 2A output for mobile devices.
• Lunghezza del cavo: Approximately 125cm (4.1Ft) recliner switch cable.
• Compatibilità: Works with Okin, Ashley Furniture, Dewert, Flexteel, Limoss, and many other power recliners using a 5-pin connection.

Okin 2 Button 5 Pin Recliner Hand Control with USB, showing the two control buttons and the USB charging port.

Configurazione e installazione

This section details the steps for replacing or installing the hand control unit.

Strumenti necessari: Small flat-head screwdriver or putty knife (for prying), zip ties (optional, for cable management).

Fasi di installazione:

1. Scollegare l'alimentazione: Ensure the recliner is unplugged from the electrical outlet before beginning installation.
2. Rimuovi vecchio controllo: Carefully remove the existing hand control unit from its mounting location. This may involve gently prying it out of the armrest or side panel.
3. Scollegare il cavo: Disconnect the 5-pin connector of the old control from the recliner's motor or control box.
4. Connetti nuovo controllo: Connect the new Okin 2 Button 5 Pin Hand Control's cable to the recliner's control box. Ensure the 5-pin connector is securely seated.
5. Cavo di percorso: Route the cable neatly and secure it with zip ties if necessary to prevent snagging or damage.
6. Unità di installazione: Insert the new hand control unit into the mounting hole. Ensure it clicks into place or is securely fastened using the provided circlips.
7. Ricollegare l'alimentazione: Reconnect the recliner to the electrical outlet.

Esploso view diagram illustrating the components of the recliner hand control and its installation into a wooden frame, showing the switch cover, lower cover, circlips, and studs.

Close-up of the 5-pin connector, which connects the hand control to the recliner's motor system.

Istruzioni per l'uso

The Okin 2 Button 5 Pin Hand Control provides simple operation for your power recliner.

Funzione reclinabile:

• Extend Footrest / Recline: Premere e tenere premuto il tasto "SU" button to extend the footrest and recline the chair.
• Retract Footrest / Upright: Premere e tenere premuto il tasto "GIÙ" button to retract the footrest and return the chair to its upright position.
• Nota: Some recliner models may require continuous pressure on the button for the full range of motion.

Porta di ricarica USB:

• The integrated USB port (5V 2A) is designed for charging mobile devices. Connect your device's USB cable to the port.
• Ensure the recliner is connected to a power source for the USB port to function.

Manutenzione

To ensure the longevity and proper function of your hand control unit:

• Pulizia: Keep the unit clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents, which can damage the surface or internal components.
• Ispezione dei cavi: Ensure cables are not pinched, twisted, or damaged. Regularly inspect the cable for any signs of wear, fraying, or cuts.
• Condizioni ambientali: Do not expose the unit to excessive moisture, direct sunlight, or extreme temperatures.

Risoluzione dei problemi

L'unità di controllo non risponde:

1. Controllo dell'alimentazione: Verify that the recliner is properly plugged into a working power outlet.
2. Verifica della connessione: Ensure that all cable connections, especially the 5-pin connector to the recliner's motor, are secure and fully inserted.
3. Danni al cavo: Inspect the control cable for any visible damage or cuts. A damaged cable may prevent proper function.
4. Motor/Power Supply: If the issue persists after checking connections and cable, the recliner's motor or power supply unit may need inspection by a qualified technician.

Porta USB non in carica:

1. Recliner Power: Ensure the recliner is powered on and connected to an electrical outlet. The USB port requires power from the recliner's system.
2. Cable/Device Check: Prova un cavo USB o un dispositivo diverso per escludere problemi con il cavo di ricarica o con il dispositivo in carica.
3. Sostituzione dell'unità: If the USB port still does not function, the control unit may require replacement.

Specifiche

Detailed dimensions of the Okin 2 Button 5 Pin Recliner Hand Control, showing measurements of 3.27 inches, 1.42 inches, and 3.9 inches.

Posteriore view of the control unit, displaying product identification labels including P/N JLDK-17, DC 24V 2A, USB 5V 2A, and manufacturer Okin Refined Electric Technology Co., Ltd.

Garanzia e supporto

For warranty information or technical support regarding this Okin 2 Button 5 Pin Recliner Hand Control, please refer to the documentation provided with your original recliner or contact the manufacturer directly. Specific warranty terms for this replacement part may vary.