Manuale utente del controller DENALI CANsmart GEN II per motociclette BMW R1200LC e R1250

Introduzione

The DENALI CANsmart Controller GEN II is an advanced accessory management system designed specifically for BMW R1200LC and R1250 series motorcycles. This device provides plug-and-play installation and intelligent control of up to four DENALI accessories, such as auxiliary lights, horns, and brake lights, directly through the motorcycle's CAN bus system. It simplifies wiring and offers customizable settings for various functions, enhancing both safety and convenience.

Contenuto della confezione

Verifica che tutti gli articoli elencati di seguito siano presenti nel tuo pacco:

• DENALI CANsmart Controller GEN II Unit
• Wiring Harnesses for Accessory Circuits (Red, Blue, Yellow, White)
• CAN Bus Connector Cable
• Battery Terminal Connectors with Main Fuse
• Cavo di programmazione USB
• Cravatte con zip
• Pad di montaggio adesivo

Immagine: Contents of the DENALI CANsmart Controller GEN II package, including the main controller unit, various wiring harnesses, battery connectors, USB cable, zip ties, and an adhesive pad.

Informazioni sulla sicurezza

Before installation and operation, please read and understand all safety warnings and instructions. Failure to do so may result in property damage, injury, or death.

• Prima di effettuare qualsiasi intervento elettrico, scollegare sempre la batteria della motocicletta.
• Assicurarsi che tutti i collegamenti siano sicuri e adeguatamente isolati per evitare cortocircuiti.
• Do not exceed the maximum current ratings for each circuit (10A continuous, 25A maximum for 25 seconds) or the total system (25A continuous).
• Consult a qualified motorcycle technician if you are unsure about any part of the installation process.
• Keep wiring away from hot engine components and moving parts.

Configurazione e installazione

Follow these steps for proper installation of your DENALI CANsmart Controller GEN II.

Passaggio 1: preparare la moto

1. Parcheggiare la motocicletta su una superficie piana e assicurarsi che sia stabile.
2. Spegnere il motore e togliere la chiave.
3. Disconnect the negative terminal of the motorcycle's battery.
4. Remove any necessary body panels or seats to access the CAN bus connector and battery.

Step 2: Connect the CANsmart Controller

1. Locate the motorcycle's CAN bus connector. Refer to your motorcycle's service manual for its exact location (often under the seat or near the diagnostic port).
2. Connect the CAN bus connector cable from the CANsmart Controller to the motorcycle's CAN bus port. This is a plug-and-play connection.
3. Connect the battery terminal wires from the CANsmart Controller to the motorcycle's battery terminals. Ensure the red wire connects to the positive (+) terminal and the black wire connects to the negative (-) terminal. The main fuse is integrated into the positive wire.

Immagine: The DENALI CANsmart Controller GEN II unit installed discreetly under the seat of a BMW motorcycle, showing its compact size and integration with existing wiring.

Passaggio 3: collegare gli accessori

1. Identify which of the four accessory circuits (Red, Blue, Yellow, White) you will use for each accessory. Each circuit has a 10A continuous rating.
2. Connect your DENALI accessories (e.g., auxiliary lights, horn, brake light) to the corresponding CANsmart circuit harnesses. Ensure proper polarity.
3. Route all wiring neatly and securely using the provided zip ties, keeping them away from heat sources and moving parts.

Immagine: A detailed wiring diagram illustrating the connections for the DENALI CANsmart Controller. It shows the main unit, CAN bus connector, battery terminals with a 30A fuse, and the four accessory circuits (White, Yellow, Blue, Red), each rated for 10A.

Step 4: Secure the Controller

Use the adhesive mounting pad to secure the CANsmart Controller unit in a safe, dry location, typically under the seat or within a fairing, ensuring it is not exposed to direct elements or excessive heat.

Passaggio 5: ricollegare la batteria e testare

1. Reconnect the negative terminal of the motorcycle's battery.
2. Turn on the ignition and perform initial tests of your connected accessories.

Software Configuration and Operating Instructions

The CANsmart Controller's full functionality is accessed and customized via the DENALI CANsmart software, available for download from the DENALI website. This software allows you to assign specific functions to each of the four circuits and adjust their behavior.

Connessione al software

1. Download and install the DENALI CANsmart software on your computer.
2. Connect the CANsmart Controller to your computer using the provided USB programming cable.
3. Launch the CANsmart software. The software should automatically detect the connected controller.

Circuit Functions

The software interface allows you to configure each circuit independently. Common functions include:

• Light Pair 1 / Light Pair 2: For auxiliary driving lights, often with dimming, flash-to-pass, and high-beam sync features.
• Corno: For aftermarket horns, allowing integration with the motorcycle's horn button.
• Luce freno: For aftermarket brake lights, offering features like modulated braking or deceleration-activated lighting.
• Accessorio: A general-purpose switched power output for other accessories.

Immagine: Screenshot of the DENALI CANsmart software interface, showing options to configure the Red, Blue, Yellow, and White circuits. Icons represent various functions like Light Pair 1, Horn, Brake Light, and Accessory, with options to apply or cancel changes.

Regolazione delle impostazioni

Within the software, you can adjust parameters such as:

• Light intensity (dimming).
• Flash patterns for brake lights.
• Horn behavior.
• Trigger conditions for accessories (e.g., ignition on, high beam active).

Refer to the software's built-in help or the DENALI website for detailed instructions on each function and setting.

Manutenzione

The DENALI CANsmart Controller GEN II is designed for maintenance-free operation. Periodically inspect the wiring and connections for any signs of wear, corrosion, or damage. Ensure the controller unit remains securely mounted and free from excessive moisture or heat.

• Pulizia: Wipe the controller unit with a dry, soft cloth if it becomes dirty. Do not use harsh chemicals or abrasive cleaners.
• Aggiornamenti del firmware: Check the DENALI website periodically for firmware updates for your CANsmart Controller. Updates can be installed via the CANsmart software and USB cable.

Risoluzione dei problemi

If you encounter issues with your CANsmart Controller, refer to the following common problems and solutions:

If the problem persists, contact DENALI customer support for further assistance.

Specifiche

• Modello: DNL.WHS.11602
• Ingresso volumetage: 12V DC (Motorcycle Battery)
• Numero di circuiti: 4 (Red, Blue, Yellow, White)
• Valutazione del circuito: 10A continuous per circuit, 25A maximum for 25 seconds per circuit
• Total System Current: 25A continuo
• Compatibilità: BMW R1200LC & R1250 series motorcycles
• Connettività: CAN Bus, USB for programming
• Dimensioni: Approximately 7 x 5 x 2 inches (Package Dimensions, actual unit is smaller)
• Peso: Approximately 1 pound (Item Weight)

Informazioni sulla garanzia

DENALI products are covered by a limited warranty against defects in materials and workmanship. The specific warranty period and terms may vary. Please retain your proof of purchase. For detailed warranty information, please visit the official DENALI websito o contattare l'assistenza clienti.

Supporto

For technical assistance, troubleshooting, or further inquiries regarding your DENALI CANsmart Controller GEN II, please visit the DENALI Electronics websito o contattare il loro team di assistenza clienti.

Websito: www.denalielectronics.com

Fare riferimento al websito per le informazioni di contatto e le risorse di supporto più aggiornate.