Fruhdi KDPT007-115 Recliner Motor Actuator Kit

1. Introduzione

The Fruhdi KDPT007-115 is a replacement linear actuator motor designed for electric recliners, massage chairs, and lift beds. This manual provides essential information for the safe installation, operation, and maintenance of your actuator kit. Please read this manual thoroughly before attempting any installation or operation.

2. Informazioni sulla sicurezza

• Always disconnect power to the recliner or lift chair before performing any installation, maintenance, or inspection.
• The maximum load capacity for this actuator is 1500N (approximately 153 kg or 337 lbs). Do not exceed this limit.
• Usa solo un KD Power Supply with this actuator. Using an incompatible power supply may cause damage or malfunction.
• Observe the duty cycle: 2 minutes ON, 18 minutes OFF (10%). Continuous operation beyond this limit can lead to overheating and permanent damage to the motor.
• Durante il funzionamento, tenere mani, capelli e indumenti larghi lontani dalle parti in movimento.
• Ensure children and pets are kept away from the recliner during operation and maintenance.

3. Contenuto della confezione

Prima di procedere con l'installazione, verificare che tutti i componenti siano presenti e integri.

• 1 x Fruhdi KDPT007-115 Recliner Motor Actuator
• 1 x Power Transformer (with 2-pin flat round connection)
• 1 x Hand Control Cable (with 5-pin plug connection)
• 1 x cavo di alimentazione CA.

Image: The complete Fruhdi KDPT007-115 actuator kit, including the motor, power supply, AC power cord, and hand control cable.

4. Specifiche

Immagine: Primo piano view of the actuator label, displaying model number, load capacity, stroke, and duty cycle specifications.

Image: Diagram illustrating the stroke length (8.90 inches) and minimum installation size (5.90 inches) of the actuator.

5. Configurazione e installazione

Installation of the Fruhdi KDPT007-115 actuator requires careful attention to detail. If you are unsure about any step, it is recommended to seek professional assistance.

1. Preparazione: Before beginning, ensure the recliner or lift chair is in a stable position and disconnect it from the main power supply.
2. Verifica compatibilità: Confirm that the model number KDPT007-115 matches your existing actuator or is compatible with your furniture's requirements. Pay close attention to the stroke length (8.90 inches) and minimum installation dimension (5.90 inches).
3. Rimuovere il vecchio attuatore: Carefully detach the old actuator from its mounting points on the chair frame. Note how it was connected to the power supply and hand control.
4. Installare il nuovo attuatore: Position the new Fruhdi KDPT007-115 actuator in the same location as the old one. Securely fasten it to the chair frame using appropriate hardware (not included, typically reused from the old actuator).
5. Connect Power Transformer: Connect the 2-pin flat round connector from the actuator to the power transformer.
6. Connect Hand Control: Plug the 5-pin connector from the hand control cable into the corresponding port on the actuator.
7. Connessioni sicure: Ensure all electrical connections are firm and properly seated to prevent intermittent operation.
8. Controllo finale: Double-check all mounting points and connections before restoring power.

Immagine: Un example of an electric recliner where the actuator would be installed, demonstrating its typical application.

6. Istruzioni per l'uso

Once the actuator is correctly installed and all connections are secure, you can begin operating your recliner.

1. Ripristina alimentazione: Plug the AC power cord into a wall outlet and ensure the power transformer is connected to the actuator.
2. Use Hand Control: Utilize the buttons on your recliner's hand control to extend or retract the actuator, thereby adjusting the chair's position.
3. Observe Duty Cycle: To prolong the life of the actuator, avoid continuous operation. Adhere to the 2 minuti ON / 18 minuti OFF duty cycle. Allow the motor to cool down between extended uses.

7. Manutenzione

Regular maintenance helps ensure the longevity and proper function of your Fruhdi KDPT007-115 actuator.

• Pulizia: Wipe the exterior of the actuator and cables with a clean, dry cloth. Do not use liquid cleaners or abrasive materials.
• Ispezione: Periodically inspect all cables, connections, and mounting points for signs of wear, fraying, or damage. Replace any damaged components immediately.
• Controllo degli ostacoli: Ensure that the actuator's moving parts are free from any obstructions, such as fabric, debris, or foreign objects.
• Lubrificazione: The actuator is factory-lubricated. Do not attempt to lubricate internal components unless specifically instructed by the manufacturer.

8. Risoluzione Dei Problemi

If you encounter issues with your Fruhdi KDPT007-115 actuator, refer to the following troubleshooting steps:

Se le procedure di risoluzione dei problemi non risolvono il problema, contattare l'assistenza clienti per ulteriore assistenza.