Introduzione
This manual provides essential information for the safe and effective use of the BENNING EV 3-2 Measuring Adapter. The EV 3-2 is designed for simulating charging conditions and testing the effectiveness of protective measures at 1 and 3-phase e-charging stations. It facilitates safety and functional tests in accordance with DIN VDE 0100-600 (IEC 60364-6) and DIN VDE 0105-100 (EN 50110) when used with BENNING IT 130 and IT 200 installation testers. The adapter is intended for testing charging stations compliant with DIN EN / IEC 61851-1 (VDE 0122-1) for charging mode "Mode 3" and features a Type 2 connector according to IEC / EN 62196. It ensures secure contact with the installation tester and initiates the charging process by simulating an electric vehicle.
Contenuto della confezione
Dopo aver aperto la confezione, verificare che tutti i componenti siano presenti e integri:
- BENNING EV 3-2 Measuring Adapter
- Custodia protettiva
Image: The protective case for the BENNING EV 3-2 Measuring Adapter, designed for safe storage and transport.
Impostare
Follow these steps to set up the BENNING EV 3-2 Measuring Adapter for testing:
- Connect to EVSE: Plug the Type 2 connector of the EV 3-2 adapter into the charging station (EVSE) to be tested. Ensure a secure connection.
- Connect to Installation Tester: Utilize the test sockets and 4mm sockets on the EV 3-2 to connect it to a compatible BENNING installation tester (e.g., IT 130 or IT 200).
- Verify Phase Display: Observe the three LEDs on the adapter for separate phase display, which allows for easy voltage controllo.
Image: A diagram illustrating the connection of the BENNING EV 3-2 Measuring Adapter between an EVSE charging station and an installation tester, demonstrating the typical setup for testing.
Istruzioni per l'uso
The BENNING EV 3-2 Measuring Adapter facilitates comprehensive testing of EV charging stations. Key functionalities include:
- Proximity Pilot (PP) Check: The adapter checks the charging cable coding via the Proximity Pilot (PP) signal to correctly limit the charging current.
- Control Pilot (CP) Simulation: The Control Pilot (CP) function allows for the simulation of various vehicle statuses (A, B, C, D, and E, including short circuit between CP-PE) to trigger and control the charging process.
- CP Signal Output: A BNC connector is provided for CP signal output, enabling detailed analysis with an oscilloscope if required.
- Voltage Controllo: The integrated LEDs provide a clear, separate display for each phase, simplifying voltage verification during tests.
Image: The BENNING EV 3-2 Measuring Adapter, showcasing its control panel with indicators for PP and CP status, phase LEDs, and connection ports for comprehensive testing of EVSE.
Manutenzione
To ensure the longevity and accurate performance of your BENNING EV 3-2 Measuring Adapter, follow these maintenance guidelines:
- Pulizia: Pulire il dispositivo con un panno morbido e asciutto. Non utilizzare detergenti abrasivi o solventi.
- Magazzinaggio: Store the adapter in its protective case when not in use to prevent damage from dust, moisture, and physical impact. Keep it in a cool, dry place.
- Ispezione: Regularly inspect the cables, connectors, and housing for any signs of wear, damage, or loose connections. Do not use the device if any damage is observed.
- Calibrazione: For professional use, periodic calibration by authorized service personnel is recommended to maintain measurement accuracy. Refer to BENNING's official guidelines for calibration intervals.
Risoluzione dei problemi
This section addresses common issues you might encounter with the BENNING EV 3-2 Measuring Adapter.
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Adapter not recognized by EVSE. | Loose connection; EVSE fault; Adapter fault. | Ensure the Type 2 connector is fully inserted. Check EVSE for error codes. Test adapter with another EVSE if possible. |
| No phase display on LEDs. | nessun volumetage from EVSE; Faulty connection to EVSE; LED malfunction. | Verify EVSE is powered and active. Re-seat the Type 2 connector. If problem persists, contact support. |
| CP simulation not working. | Incorrect CP setting; Connection issue with installation tester. | Review the desired CP status setting. Ensure secure connection to the installation tester. |
Specifiche
| Attributo | Dettaglio |
|---|---|
| Numero di modello | 044169 |
| Dimensioni del prodotto (L x P x A) | 1.97 x 7.48 x 15.75 pollici |
| Peso | 2.87 libbre |
| Marca | BENNING |
| Fonte di alimentazione | Corded Electric (via EVSE connection) |
| Paese di origine | Germania |
| Tipo di connettore | Type 2 (IEC / EN 62196) |
| Compatibilità | BENNING IT 130 and IT 200 installation testers |
Garanzia e supporto
For information regarding warranty coverage, technical support, or service, please refer to the official BENNING website or contact their customer service directly. Keep your purchase receipt and product model number (044169) readily available for any inquiries.
Produttore: BENNING
Data prima disponibilità: 26 luglio 2023