1. Introduzione
Thank you for choosing the HOBBYWING Skywalker 40A V2 UBEC Electronic Speed Controller (ESC). This manual provides essential information for the proper installation, setup, operation, and maintenance of your ESC. Please read this manual thoroughly before use to ensure safe and efficient operation.
The Skywalker 40A V2 UBEC is designed for various brushless motor applications, featuring a high-performance 32-bit microprocessor and advanced DEO (Driving Efficiency Optimization) technology for improved throttle response and efficiency.
Cosa c'è nella scatola:
- 1x HOBBYWING Skywalker 40A V2 UBEC ESC
- 1x Manuale utente (questo documento)
2. Precauzioni di sicurezza
Operating an Electronic Speed Controller requires adherence to safety guidelines to prevent injury or damage. Always observe the following:
- Collegamento della batteria: Ensure correct polarity when connecting the battery. Reverse polarity will cause immediate damage to the ESC.
- Isolamento: Properly insulate all connections to prevent short circuits.
- Compatibilità motore: Verify that your motor is compatible with the ESC's specifications.
- Ventilazione: Assicurare un flusso d'aria adeguato attorno all'ESC durante il funzionamento per evitare il surriscaldamento.
- Calibrazione dell'acceleratore: Always perform throttle range calibration before the first flight or after changing your transmitter.
- Disconnessione dell'alimentazione: Disconnect the battery from the ESC immediately after use.
- Acqua e umidità: Keep the ESC away from water and moisture unless it is specifically rated as waterproof.
3. Prodotto finitoview
The HOBBYWING Skywalker 40A V2 UBEC is a high-performance Electronic Speed Controller designed for remote-controlled aircraft. It integrates advanced features for reliable and efficient power management.
Figure 3.1: HOBBYWING Skywalker 40A V2 UBEC ESC with power and signal wires, and motor connectors.
Caratteristiche principali:
- High-performance 32-bit ARM M0 processor (up to 96MHz) supporting maximum speeds of 300,000 RPM (2-pole motor).
- DEO (Driving Efficiency Optimization) Technology for fast throttle response, improved stability, and higher driving efficiency.
- BEC Output: 5V @ 5A (Switch-mode) for powering receiver and servos.
- Supports 3-4S LiPo batteries.
- Multiple brake modes: Normal Brake, Reverse Brake, Linear Reverse Brakes, and Brake Disabled.
- Search Mode to locate lost aircraft by motor beeps.
- Programmable via LED Program Box or transmitter.
- Comprehensive protection features: start-up, ESC thermal, capacitor thermal, over-current, over-load, abnormal input voltage, and throttle signal loss.
Figura 3.2: Dall'alto verso il basso view of the HOBBYWING Skywalker 40A V2 UBEC ESC, illustrating its compact design and wire lengths.
4. Impostazione
4.1 Schema elettrico
Connect the ESC to your motor, battery, and receiver as shown in the general wiring diagram below. Ensure all connections are secure and correctly polarized.
- Collegamento della batteria: The red wire connects to the positive (+) terminal of your LiPo battery, and the black wire connects to the negative (-) terminal.
- Collegamento del motore: The three black wires from the ESC connect to the three wires of your brushless motor. The order of connection may affect motor rotation direction; swap any two wires to reverse direction if needed.
- Collegamento del ricevitore: The three-wire servo connector (usually brown, red, orange/yellow) plugs into the throttle channel of your receiver.
4.2 Calibrazione della gamma dell'acceleratore
Throttle calibration is crucial for the ESC to correctly recognize the throttle signals from your transmitter. Perform this procedure before the first use or if you change your transmitter.
- Turn on your transmitter and set the throttle stick to its maximum position (100% throttle).
- Collega la batteria all'ESC. Il motore emetterà una serie di segnali acustici.
- When you hear a specific tone (refer to the full manual for exact tone sequence), move the throttle stick to its minimum position (0% throttle).
- The ESC will emit another series of tones, indicating successful calibration.
- Disconnect the battery. The ESC is now calibrated and ready for use.
4.3 Programmazione dell'ESC
The Skywalker 40A V2 UBEC ESC can be programmed using a HOBBYWING LED Program Box or directly via your transmitter. Refer to the user manual of the HOBBYWING LED Program Box for detailed instructions on its use.
- Scatola di programmazione LED: Connect the program box to the dedicated programming port on the ESC. This method offers a clear interface for adjusting parameters.
- Programmazione del trasmettitore: This method involves specific throttle stick movements and listening to motor beeps to select and confirm settings. Consult the detailed HOBBYWING ESC manual for the precise sequence.
5. Operativo
5.1 Funzionamento normale
After successful setup and calibration, connect the battery, and the ESC will initialize. Move the throttle stick to control motor speed. The DEO (Driving Efficiency Optimization) technology ensures a fast and smooth throttle response, enhancing flight stability and efficiency.
5.2 Brake Modes
The ESC supports various brake modes, which can be configured through programming:
- Brake Disabled: The motor will freewheel when the throttle is at minimum.
- Normal Brake Mode: Applies a braking force when the throttle is at minimum. The brake amount is adjustable.
- Reverse Brake Mode: Allows the motor to reverse direction, effectively shortening landing distances for aircraft. This mode can be linear for precise control.
5.3 Modalità di ricerca
The Search Mode feature assists in locating your aircraft if it lands in a visually obstructed area. When activated (typically through a specific transmitter input or after a period of inactivity), the ESC will pulse the motor to emit audible beeps, guiding you to its location. This mode can also serve as a reminder to disconnect the battery after a set idle time to prevent over-discharge.
6. Manutenzione
Proper maintenance ensures the longevity and reliable performance of your ESC.
- Pulizia: Regularly inspect the ESC for dirt, dust, or debris. Use a soft brush or compressed air to gently clean the unit. Avoid using liquids unless the ESC is specifically rated for it.
- Ispezione del filo: Controllare periodicamente tutti i cavi e i connettori per verificare la presenza di segni di usura, sfilacciamento o corrosione. Sostituire immediatamente i componenti danneggiati.
- Magazzinaggio: Store the ESC in a cool, dry place away from direct sunlight and extreme temperatures. Disconnect all batteries before storage.
- Aggiornamenti del firmware: Controlla l'Hobbywing website for any available firmware updates for your ESC model. Follow the instructions provided by Hobbywing for any update procedures.
7. Risoluzione Dei Problemi
This section addresses common issues you might encounter with your HOBBYWING Skywalker 40A V2 UBEC ESC.
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Il motore non si avvia o balbetta | Incorrect throttle calibration; Motor/ESC connection issue; Low battery voltage; Motor timing issue. | Recalibrate throttle range; Check all motor and battery connections; Charge battery; Adjust motor timing via programming. |
| L'ESC si surriscalda | Insufficient airflow; Over-gearing/overloading motor; Short circuit in motor or wiring. | Ensure proper ventilation; Reduce propeller size or load; Inspect motor and wiring for damage. |
| Il motore gira nella direzione sbagliata | Collegamento errato del cavo del motore. | Scambia due dei tre fili del motore. |
| Nessuna risposta dall'ESC | No power to ESC; Receiver not connected; Throttle signal loss. | Check battery connection; Ensure receiver is powered and connected to ESC; Check transmitter and receiver. |
| ESC emits continuous beeps | Basso volumetage cutoff; Throttle signal loss; Start-up failure. | Charge battery; Check receiver connection; Ensure throttle is at zero during power-up. |
The ESC features multiple protection mechanisms (start-up, thermal, over-current, etc.) that may cause it to stop operating. If an issue persists, consult the detailed HOBBYWING product manual or contact customer support.
8. Specifiche
Below are the technical specifications for the HOBBYWING Skywalker 40A V2 UBEC ESC:
- Modello: Skywalker 40A V2 UBEC
- Corrente continua: 40A
- Corrente di scoppio: 60A (per 10 secondi)
- Ingresso volumetage: 3-4S LiPo
- Uscita BEC: 5 V a 5 A (modalità di commutazione)
- Processore: High-performance 32-bit ARM M0 (up to 96MHz)
- Max RPM (2-pole motor): 300,000 giri al minuto
- Dimensioni: Circa 4.6 x 0.75 x 8.15 pollici (117 x 19 x 207 mm)
- Peso: Circa 1.6 once (45 grammi)
- Produttore: Tecnologia Hobbywing
9. Garanzia e supporto
Per informazioni sulla garanzia e supporto tecnico, fare riferimento al sito ufficiale Hobbywing website or contact your local Hobbywing distributor. Warranty terms typically cover manufacturing defects for a specified period from the date of purchase. Please retain your proof of purchase for warranty claims.
Produttore: Tecnologia Hobbywing
Per ulteriore assistenza, visitare www.hobbywing.com.
