Manuale di istruzioni del drone Swellpro Fisherman MAX FD2 versione avanzata

1. Introduzione

This manual provides essential instructions for the safe and effective operation of your Swellpro Fisherman MAX FD2 Advanced Version Heavy Lift Fishing Drone. Please read this manual thoroughly before your first flight and retain it for future reference. This drone is designed for heavy-lift fishing applications, featuring a 4K camera, 3.5kg bait release capacity, and IP67 waterproofing.

2. Informazioni sulla sicurezza

Always operate the drone in open areas, away from people, animals, and obstacles. Ensure all components are securely attached and functioning correctly before each flight. Adhere to all local regulations regarding drone operation. Avoid flying in strong winds or adverse weather conditions. Do not attempt to modify the drone or its components, as this may compromise safety and void the warranty.

3. Prodotto finitoview

The Swellpro Fisherman MAX FD2 includes the following main components:

• Fisherman Max Drone (Advanced) x1
• Gimbal Camera (GC1-M) x1
• Dual Payload Release (DPL) x1
• Float (FL-FD2) x1 + FD2 Case x1
• Propellers (P-FD2) x2 + Intelligent Battery (B-FD2) x1
• Telecomando

Figure 3.1: Swellpro Fisherman MAX FD2 Drone, remote controller, battery, and propellers.

4. Impostazione

4.1. Disimballaggio e montaggio iniziale

1. Place the carry case on a flat surface and open it.
2. Remove the accessory pack and set it aside.
3. Carefully take out the aircraft and place it on a flat platform.

4.2. Installazione della batteria

1. Align the flight battery slot with the pin connector inside the drone's compartment.
2. Gently push the battery into place until it is fully seated.
3. Lock the four latches (numbered 1 to 4) to securely fasten the battery.

Video 4.1: Swellpro Fisherman MAX FD2 Setup Guide. This video demonstrates the initial setup steps, including battery installation and arm unfolding.

4.3. Arm Unfolding

1. Unfold the front arms, marked with 'F'.
2. Then, unfold the rear arms, marked with 'R'.
3. Rotate the ring in the direction of the arrow on each arm to tighten it securely.

4.4. Floating Bar Installation (Optional)

The Fisherman MAX FD2 does not float on water by itself. Attaching the four floating bars is recommended if you intend to fly close to or land on the water.

1. Remove the straps from each floating bar.
2. Place a floating bar under each arm of the drone.
3. Secure the floating bars by locking the latches.

4.5. Camera Protection Removal

1. Carefully remove the protection foam from the camera gimbal before flight.

4.6. Installazione dell'elica

1. Take the propellers out of the case.
2. Place the orange-marked propellers onto the orange-marked motors. Rotate the mount counter-clockwise to tighten.
3. Place the black-marked propellers onto the black-marked motors. Rotate the mount clockwise to tighten.

Video 4.2: How to Install FD3 and FD1+ Drone Propellers. This video demonstrates the correct method for installing propellers on Swellpro drones.

4.7. Regolazione dell'antenna

1. For better transmission at high altitudes, tilt the drone's antennas down.
2. When flying close to the water surface, tilt the drone's antennas up.

4.8. Configurazione del telecomando

1. If using a smartphone for the app, install the phone holder onto the remote controller by turning the screw clockwise to secure it.
2. Adjust the direction of the remote controller's antennas perpendicular to the aircraft for optimal signal.
3. Ensure all toggles on the remote controller are switched to the 'up' position before powering on.
4. Short press the power button once, then long press for 2 seconds to power on the remote controller.

Figure 4.1: Swellpro Fisherman MAX FD2 Remote Controller. This image shows the remote controller with its screen and joysticks.

4.9. Powering On the Aircraft

1. To power on the aircraft, short press the power button underneath the aircraft once, then long press for 2 seconds.

4.10. Lista di controllo pre-volo

Before each flight, you must go through the following checklist:

1. There are no damages on the propellers.
2. The battery is firmly locked.
3. The antennas are tightened.
4. All the payloads are firmly attached.
5. The sealing flap over the USB port of the remote controller is closed.
6. The Micro SD card is inserted into the camera with the sealing flap closed.

5. Istruzioni per l'uso

5.1. Controllo remoto finitoview

The remote controller provides real-time flight data and control over the drone. Ensure the remote is powered on and connected to the drone before attempting flight.

5.2. Controlli di volo

Familiarize yourself with the joystick controls:

• Joystick sinistro: Controls vertical position (throttle) and yaw (rotation).
• Joystick destro: Controls horizontal movement (forward, backward, left, right).

Video 5.1: Fisherman FD1+ First Flight Flying Tutorial. This video provides a basic tutorial on drone flight controls.

5.3. Rilascio dell'esca

The drone is equipped with a Dual Payload Release (DPL) system for bait deployment.

1. Securely attach your bait to the payload release mechanism.
2. Fly the drone to your desired bait drop location.
3. Press the designated payload switch on the remote controller to release the bait.

Video 5.2: FD1+ Drop Bait Tutorial. This video demonstrates the process of attaching and releasing bait using a Swellpro drone.

Figure 5.1: Swellpro Fisherman MAX FD2 Drone ready for flight on a beach.

5.4. Ritorno a casa (RTH)

The drone features an automatic Return to Home function for safe retrieval.

1. To activate RTH, press the dedicated 'Return to Home' switch on the remote controller.
2. The drone will automatically fly back to its takeoff point and land.

6. Manutenzione

6.1. Post-Flight Cleaning

After each flight, especially in saltwater environments, it is crucial to rinse the drone thoroughly with fresh water. This prevents sand or salt buildup, which can affect performance and longevity. Never skip this step for maximum longevity.

6.2. Conservazione

Store the drone and its components in a cool, dry place, away from direct sunlight and extreme temperatures. Ensure batteries are charged to storage voltage (typically 50-60%) if storing for extended periods.

7. Risoluzione Dei Problemi

If you encounter issues with your drone, consider the following general troubleshooting steps:

• Il drone non si accende: Check battery charge level and ensure it's correctly installed and latched.
• Il telecomando non si connette: Ensure both drone and remote are powered on and within range. Check remote battery level.
• Volo instabile: Perform IMU calibration. Check for damaged propellers and replace if necessary. Ensure arms are fully unfolded and tightened.
• Problemi con il segnale GPS: Assicurati di essere in un'area aperta con una chiara view of the sky. Wait for sufficient satellite connections (at least 9 satellites recommended).
• Bait release failure: Check the payload switch on the remote and ensure the bait is correctly attached to the DPL mechanism.

For persistent issues, refer to the official Swellpro support resources or contact customer service.

8. Specifiche

9. Garanzia e supporto

For warranty information, technical support, or service inquiries, please refer to the official Swellpro webo contattare il rivenditore autorizzato. Conservare la prova d'acquisto per eventuali reclami in garanzia.