Manuale di istruzioni dell'ESC HOBBYWING Skywalker 60A V2

Prodotto finitoview

The HOBBYWING Skywalker 60A V2 Electronic Speed Controller (ESC) is designed for remote-controlled aircraft, offering reliable performance and advanced features. This manual provides essential information for proper installation, operation, and maintenance of your ESC.

Informazioni importanti sulla sicurezza

Please read and understand all safety precautions before using this unit. Failure to follow these instructions may result in damage to the product, property, or personal injury.

• Review manuals for all power devices and aircraft to ensure a rational power configuration.
• Ensure all wires and connections are properly insulated before connecting the ESC to related devices. Short circuits can damage the ESC.
• Verify all devices are securely connected to prevent poor connections that could lead to loss of aircraft control or device damage. Use a soldering iron with sufficient power for all input/output wires and connectors if necessary.
• Never allow the motor to lock up during high-speed rotation. This can destroy the ESC and damage the motor. Immediately move the throttle stick to the bottom position or disconnect the battery if the motor locks up.
• Avoid using the unit in extremely hot weather or continuing operation when it becomes excessively hot. High temperatures can activate thermal protection or cause permanent damage to the ESC.
• Always disconnect and remove batteries after use. The ESC will continue to consume current if connected, leading to complete battery discharge and potential damage to batteries or the ESC. Such damage is not covered under warranty.

Contenuto della confezione

• (1) HOBBYWING Skywalker 60A V2 ESC
• (1) Manuale di istruzioni

Guida all'installazione

Proper installation is crucial for optimal performance and safety. Follow these steps to set up your Skywalker 60A V2 ESC:

1. Collegamento al motore: Connect the three output wires from the ESC to the three wires of your brushless motor. Ensure correct phase connection for proper motor rotation. If the motor rotates in the wrong direction, swap any two of the ESC's output wires.
2. Connetti al ricevitore: Plug the signal cable (usually a three-wire servo connector) from the ESC into the throttle channel of your RC receiver.
3. Collegamento alla batteria: Connect the main power input wires (red and black) of the ESC to your LiPo battery. Ensure polarity is correct (red to positive, black to negative).

Figura 1: Fronte view of the HOBBYWING Skywalker 60A V2 ESC, showing the main unit with power and signal wires.

Figura 2: Angolato view of the HOBBYWING Skywalker 60A V2 ESC, highlighting the various wire connections for power, motor, and signal.

Istruzioni per l'uso

The Skywalker 60A V2 ESC offers various programmable features to optimize your aircraft's performance. These can be configured using a compatible HOBBYWING program box or a transmitter.

Caratteristiche principali:

• Freno di retromarcia: Features Reverse Brake and Linear Reverse Brake modes to shorten landing distances, simulating real aircraft landings. Normal Brake Mode and Brake Disabled mode are also available, with adjustable brake amounts in normal mode.
• Processore ad alte prestazioni: Equipped with a 32-bit ARM M0 processor running up to 96MHz, supporting motor speeds up to 300,000 RPM (2-pole motor).
• Tecnologia DEO: Driving Efficiency Optimization (DEO) technology provides fast and smooth throttle response, improved stability and flexibility during flight, higher driving efficiency for longer flight times, and lower ESC temperatures for reliable operation.
• Modalità di ricerca: Assists in locating a lost aircraft by pulsing the motor to beep, useful in visually obstructed environments. This mode can also prompt disconnection of the ESC battery after a set idle time to prevent battery damage from over-discharge.
• Molteplici funzionalità di protezione: Includes abnormal input voltage protection, ESC thermal protection, throttle signal loss (Fail Safe), and low voltage cutoff to prolong ESC lifespan.

Programmazione dell'ESC:

The ESC can be programmed using the HOBBYWING LED Program Box or a compatible transmitter. For advanced programming and firmware updates, the Multifunction LCD Program Box Pro is recommended.

Manutenzione

To ensure the longevity and optimal performance of your HOBBYWING Skywalker 60A V2 ESC, follow these maintenance guidelines:

• Keep the ESC clean and free from dust, dirt, and moisture. Use a soft, dry brush or compressed air for cleaning.
• Regularly inspect all wires and connectors for signs of wear, damage, or loose connections. Repair or replace as needed.
• Ensure adequate airflow around the ESC during operation to prevent overheating. Avoid obstructing the heatsink.
• Store the ESC in a cool, dry place away from direct sunlight and extreme temperatures.

Risoluzione dei problemi

If you encounter issues with your Skywalker 60A V2 ESC, refer to the following common problems and solutions:

• Motor not spinning: Check all connections (motor, battery, receiver). Ensure the throttle channel is correctly calibrated and the transmitter is powered on. Verify the ESC's running mode settings.
• ESC overheating: Ensure proper ventilation and airflow. Check for excessive load on the motor or incorrect gearing. Reduce the throttle input or adjust ESC settings if necessary.
• Intermittent power or signal loss: Inspect all wiring for loose connections or damage. Ensure the receiver is properly bound to the transmitter and that there is no interference.
• Motor beeps continuously: This may indicate a low voltage cutoff or throttle signal loss. Check battery voltage and transmitter connection. Refer to the Search Mode feature for aircraft recovery.

Specifiche tecniche

Garanzia e supporto

Hobbywing products are designed for high performance and reliability. Please refer to the official Hobbywing website or your local distributor for detailed warranty terms and conditions. Note that damage resulting from improper use, such as motor lock-up or continuous operation in extremely hot conditions, may not be covered under warranty.

For technical support, firmware updates, or further assistance, please visit the official Hobbywing support channels or contact your retailer.