1. Introduzione
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your LED Line Prime T8 LED Tube. Please read these instructions carefully before installation and retain them for future reference.
2. Istruzioni di sicurezza
- Always disconnect power before installation, replacement, or maintenance.
- L'installazione deve essere eseguita da un elettricista qualificato, nel rispetto delle normative elettriche locali.
- Do not use this product in environments with extreme temperatures or high humidity unless specifically rated for such conditions.
- Ensure the fixture is compatible with T8 LED tubes and the specified voltage (220-240 V).
- Do not attempt to modify or disassemble the LED tube.
- Handle the glass tube with care to prevent breakage.
3. Contenuto della confezione
Verificare che tutti i componenti siano presenti e integri al momento dell'apertura della confezione.
- 1 x LED Line Prime T8 LED Tube (150 cm)
- 1 x LED Starter/Fuse (for fluorescent fixture conversion)
Figure 1: LED Line Prime T8 LED Tube, showing the product both in its retail packaging and removed from the packaging, highlighting its full length.
Figura 2: primo piano view of the LED starter/fuse, labeled 'Only use With LED Tube 1A/250V', which is essential for converting traditional fluorescent fixtures to LED.
4. Configurazione e installazione
This LED tube is designed to replace traditional T8 fluorescent tubes. It requires either single-sided or dual-sided power connection. Ensure your fixture is compatible and wired correctly.
4.1. Converting a Fluorescent Fixture
- Scollegare l'alimentazione: Turn off the main power supply to the fixture at the circuit breaker.
- Rimuovere il vecchio tubo e il motorino di avviamento: Carefully remove the existing fluorescent tube and its starter from the fixture.
- Installare l'avviatore LED: Insert the provided LED starter/fuse into the starter socket.
- Installare il tubo LED: Insert the LED Line Prime T8 tube into the fixture's lamp holders. Ensure it is securely seated.
- Ricollegare l'alimentazione: Restore power and test the LED tube.
Nota: For fixtures with electronic ballasts, the ballast must be bypassed or removed, and the fixture rewired for direct AC input. Consult a qualified electrician for this procedure.
4.2. Wiring Diagrams (Direct AC Input)
The following diagrams illustrate the correct wiring for direct AC input (bypassing the ballast). This tube supports both single-sided and dual-sided power connections.
Figure 3: Wiring diagrams showing both single-sided and dual-sided power connections for the LED T8 tube. For single-sided power, both Live (L) and Neutral (N) connect to one end of the tube. For dual-sided power, Live (L) connects to one end and Neutral (N) to the other end.
- Single-Sided Power: Connect the Live (L) and Neutral (N) wires from the 230V AC supply to the pins on one end of the LED tube. The other end of the tube remains unconnected to power.
- Dual-Sided Power: Connect the Live (L) wire from the 230V AC supply to the pins on one end of the LED tube, and the Neutral (N) wire to the pins on the opposite end of the LED tube.
Always ensure proper insulation and secure connections to prevent electrical hazards.
5. Istruzioni per l'uso
Once installed correctly and power is supplied, the LED Line Prime T8 tube will illuminate instantly. There are no specific operating controls for the tube itself; its function is controlled by the fixture's power switch.
6. Manutenzione
- Pulizia: Scollegare l'alimentazione prima della pulizia. Utilizzare un panno morbido, asciutto o leggermenteamp cloth to wipe the surface of the tube. Do not use abrasive cleaners or solvents.
- Ispezione: Periodically inspect the tube and connections for any signs of damage or wear. If any damage is observed, disconnect power and replace the tube.
- Sostituzione: When the tube reaches the end of its lifespan, disconnect power and replace it with a new LED Line Prime T8 LED tube of the same specifications.
7. Risoluzione Dei Problemi
- Tube does not light up:
- Controllare che l'alimentazione sia collegata e accesa.
- Ensure the LED tube is correctly seated in the lamp titolari.
- Verify that the LED starter is correctly installed (if converting a fluorescent fixture).
- If the fixture had an electronic ballast, ensure it has been bypassed or removed and the fixture is wired for direct AC input.
- Controllare che i collegamenti dei cavi non siano allentati.
- Sfarfallio:
- Garantire un'alimentazione elettrica stabile.
- Verify correct wiring and connections.
- Ensure the LED tube is fully compatible with the fixture's wiring.
If problems persist, consult a qualified electrician or contact customer support.
8. Specifiche
| Caratteristica | Specificazione |
|---|---|
| Numero di modello | 202108 |
| Marca | Linea LED |
| Tipo | Tubo LED T8 |
| Consumo energetico | 22 L |
| Temperatura del colore | 4000 K (bianco neutro) |
| Flusso luminoso | 3300 lumen |
| Efficacia luminosa | 150 lm/W |
| Ingresso volumetage | 220-240 V |
| Tipo di base | G13 |
| Tipo di LED | SMD2835 |
| Angolo del fascio | 270° |
| Indice di resa cromatica (CRI) | AR > 80 |
| Durata | > 25,000 ore |
| Cicli di accensione/spegnimento | 50,000 |
| Materiale diffusore | Bicchiere |
| Lunghezza | 150 centimetri |
| Classe di efficienza energetica | D |
Figure 4: Energy efficiency label for the LED Line Prime T8 LED Tube, model 202108, indicating an energy class of D and consumption of 22 kWh/1000h. For more details, scan the QR code or visit eprel.ec.europa.eu/qr/1593927.
9. Garanzia e supporto
LED Line products are manufactured to high-quality standards. For warranty information, please refer to the terms and conditions provided at the point of purchase or visit the official LED Line websito. Per assistenza tecnica o richieste, contattare direttamente il rivenditore o il produttore.
