Prodotto finitoview
The ENGINEER SS-03 Solder Suction Device is an advanced desoldering pump designed for efficient solder removal. Its key innovation lies in a flexible, heat-resistant silicone tip that can directly contact a soldering iron without damage. This unique design allows the nozzle to fully 'envelope' the solder joint, significantly enhancing suction power and minimizing residual solder after each use. The device is engineered for easy disassembly, facilitating quick and straightforward maintenance.
The SS-03 model includes two spare silicone tubes (SS-16 and SS-17) of different widths, which can be cut to size to provide multiple fresh nozzles, ensuring prolonged usability.
Caratteristiche principali
- Prodotto in Giappone: Ensures high-quality manufacturing and reliability.
- Innovative Silicone Nozzle: Allows closer placement to the soldering iron tip for superior suction and improved solder removal.
- Design compatto: Enables easy one-handed operation for convenience and precision.
- Resistenza al calore: Withstands direct contact with soldering iron tips up to 350°C (662°F).
- Highest Quality Construction & Components: Built for durability and consistent performance.
- Accessori inclusi: Comes with one SS-16 (4mm outer diameter) and one SS-17 (3mm outer diameter) 50mm long silicone tube for replacement nozzles.
Impostare
The ENGINEER SS-03 Solder Suction Device comes pre-assembled and ready for immediate use. Ensure the silicone tip is securely attached to the nozzle. If replacing the tip, select the appropriate diameter (SS-16 or SS-17) and cut it to your desired length for optimal performance. The device is designed for intuitive, one-handed operation.
Figure 1: The ENGINEER SS-03 Solder Suction Device with included silicone tubes.
Istruzioni per l'uso
- Preparare il dispositivo: Push the plunger down until it clicks into place, cocking the suction mechanism.
- Riscaldare il giunto di saldatura: Using a soldering iron, heat the solder joint you wish to desolder until the solder melts and becomes liquid.
- Posizionare l'ugello: While the solder is molten, quickly place the silicone nozzle of the SS-03 directly over the molten solder joint. The flexible silicone tip is designed to make direct contact with the soldering iron tip and 'envelope' the joint for maximum suction.
- Attiva aspirazione: Press the release button on the side of the device. The plunger will rapidly retract, creating a strong vacuum that sucks the molten solder into the device's collection chamber.
- Ripetere se necessario: For larger solder joints or stubborn residue, you may need to repeat the process.
Figure 2: Proper positioning of the SS-03 nozzle over a molten solder joint.
Figure 3: Illustration of the powerful suction action of the SS-03.
The flexible silicone nozzle is a key advantage, allowing for a tight seal around the solder joint, unlike rigid Teflon nozzles that often leave a gap, as shown in the comparison below.
Figure 4: Comparison illustrating the superior 'envelope' action of the flexible silicone nozzle (right) versus a standard Teflon nozzle (left).
Manutenzione
Regular cleaning is essential to maintain the optimal suction power and longevity of your SS-03 device. The device is designed for easy disassembly for cleaning.
- Smontaggio: Unscrew the front section of the device to access the internal components and the solder collection chamber.
- Remove Solder Residue: Carefully remove any accumulated solder from the chamber and the internal plunger mechanism. Small brushes or picks can be used for thorough cleaning.
- Clean Silicone Tip: Inspect the silicone tip for any damage or excessive wear. Clean any solder residue from inside and outside the tip. If the tip is worn or damaged, replace it with a fresh section from the included SS-16 or SS-17 tubes.
- Lubrificazione (facoltativa): For smoother operation, a small amount of silicone grease (not included) can be applied to the screw threads and the internal shaft during reassembly.
- Rimontaggio: Reassemble the device by screwing the front section back onto the main body. Ensure all parts are securely fastened.
Nota importante: Do not unscrew the top plunger mechanism, as this can compromise the device's suction capability.
Risoluzione dei problemi
- Aspirazione debole: This is most commonly caused by accumulated solder inside the device. Perform a thorough cleaning as described in the Maintenance section. Also, check if the silicone tip is properly seated and not damaged, as a poor seal will reduce suction.
- Solder Not Fully Removed: Ensure the solder is fully molten before activating suction. Position the nozzle as close as possible to the joint to create an effective seal.
- Plunger Sticks: Clean the internal shaft and apply a small amount of silicone grease if necessary to ensure smooth movement.
Specifiche tecniche
| Marca | INGEGNERE |
| Numero di modello | SS-03 |
| Capacità del cilindro | 9cc |
| Materiale | Alluminio, Silicone |
| Materiale della maniglia | Alluminio |
| Lunghezza dell'articolo | 6 Inches (approx. 153mm) |
| Peso dell'articolo | 48 grammi (1.69 once) |
| Upper Temperature Rating (Silicone Tip) | 350°C (662°F) |
| Componenti inclusi | SS-17 Silicone tube x 1, SS-16 Silicone tube x 1 |
Figure 5: Approximate dimensions of the ENGINEER SS-03 (in mm).
Garanzia e supporto
For information regarding warranty coverage, technical support, or replacement parts for your ENGINEER SS-03 Solder Suction Device, please refer to the official ENGINEER webo contattare direttamente il servizio clienti. Conservare la ricevuta d'acquisto come prova d'acquisto per eventuali reclami in garanzia.
