roborock Soft Roller Brush Instruction Manual

1. Prodotto finitoview

This manual provides instructions for the roborock Soft Roller Brush, a replacement accessory designed for various roborock F25 series cordless wet dry vacuum cleaners.

Modelli compatibili:

• roborock F25
• roborock F25 GT
• roborock F25 LT
• roborock F25 RT
• roborock F25 ACE
• Roborock F25 ALT
• roborock F25 ACE Combo
• roborock F25 Combo

The roller brush is constructed from dual microfiber and nylons, designed to effectively capture food, hair, dirt, dust, pet dander, and other small particles. It is suitable for use on area rugs and sealed hard floors, including hardwood, tile, marble, laminate, and linoleum floors.

Image 1.1: The roborock Soft Roller Brush is compatible with the F25 Series Wet Dry Vacuum Cleaner.

Image 1.2: The vacuum cleaner with the soft roller brush is effective for homes with pets.

Image 1.3: The soft roller brush is designed to handle various types of spills and messes.

2. Installazione

Installazione a 2.1 maniglie

1. Align the handle with the main body of the vacuum cleaner.
2. Push the handle firmly into the designated slot until it clicks into place.
3. To remove the handle, press the release button located on the back of the main body and pull the handle upwards.

2.2 Roller Brush Installation

1. Ensure the vacuum cleaner is powered off and disconnected from the charging dock.
2. Open the roller brush cover located at the bottom of the vacuum head.
3. Align the new soft roller brush with the slots in the vacuum head.
4. Gently push the roller brush into place until it is securely seated.
5. Close the roller brush cover, ensuring it clicks firmly into position.

Image 2.1: Step-by-step visual guide for installing the handle and roller brush.

3. Funzionamento

3.1 Accensione/spegnimento e selezione della modalità

• Premere il pulsante di accensione sull'impugnatura per accendere o spegnere l'aspirapolvere.
• Use the mode selection button to switch between different cleaning modes (e.g., Normal, Eco).

3.2 Riempimento del serbatoio dell'acqua pulita

1. Locate the clean water tank, typically positioned on the main body of the vacuum cleaner.
2. Open the tank cap and fill with clean water. You may add a small amount of roborock floor cleaning solution if desired.
3. Close the tank cap securely before use.

3.3 Svuotamento del serbatoio dell'acqua sporca

1. After cleaning, detach the dirty water tank from the main body.
2. Aprire con cautela il serbatoio e smaltire l'acqua sporca.
3. Sciacquare accuratamente il serbatoio con acqua pulita e lasciarlo asciugare all'aria prima di rimontarlo.

3.4 Funzione autopulente

The vacuum cleaner features a self-cleaning function to maintain the roller brush. To initiate self-cleaning:

1. Posizionare l'aspirapolvere sulla base di ricarica.
2. Assicurarsi che il serbatoio dell'acqua pulita contenga acqua a sufficienza e che il serbatoio dell'acqua sporca sia vuoto.
3. Press the dedicated self-cleaning button (refer to your vacuum cleaner's main manual for exact button location).
4. The vacuum will automatically clean the roller brush and dry it. Voice prompts will guide you through the process.

3.5 Lay-Flat Cleaning

The roborock F25 series vacuum cleaners are designed with a lay-flat feature, allowing the main body to recline almost parallel to the floor. This enables cleaning under low-clearance furniture such as sofas and beds, reaching areas that are typically difficult to access.

4. Manutenzione

4.1 Pulizia della spazzola a rullo

Regular cleaning of the roller brush is essential for optimal performance. The brush is reusable and washable.

• After each use, or as needed, remove the roller brush from the vacuum head.
• Rinse the brush under running water to remove any trapped debris, hair, or dirt.
• Allow the roller brush to air dry completely before reinstallation to prevent odors and mildew.

Image 4.1: The soft roller brush is reusable and washable for easy maintenance.

4.2 Pulizia del filtro

The filter in the dirty water tank should also be cleaned regularly to maintain suction power and prevent blockages.

• Rimuovere il filtro dal serbatoio dell'acqua sporca.
• Tap off any loose debris and rinse the filter under running water.
• Ensure the filter is completely dry before placing it back into the tank.

4.3 Programma di sostituzione

For optimal performance and to extend the lifespan of your vacuum cleaner, it is recommended to replace the roller brush every 6 months.

5. Risoluzione Dei Problemi

If you encounter issues with your roborock Soft Roller Brush or vacuum cleaner, consider the following:

• Batteria scarica: If the vacuum announces "Low Battery," place it on the charging dock immediately.
• Self-Cleaning Not Starting: Ensure the vacuum is correctly placed on the charging dock, the clean water tank is filled, and the dirty water tank is empty.
• Prestazioni di pulizia ridotte: Check if the roller brush is clean and free of obstructions. Ensure the filter is clean and properly installed.
• La spazzola a rullo non gira: Verify that the roller brush is correctly installed and not obstructed by debris.
• Rumori insoliti: Inspect the roller brush and vacuum head for any foreign objects that might be causing the noise.

For persistent issues, refer to the main vacuum cleaner manual or contact roborock customer support.

6. Specifiche

7. Garanzia e supporto

For warranty information, please refer to the documentation included with your roborock F25 series vacuum cleaner. To ensure product longevity and optimal performance, it is recommended to purchase replacement parts, such as this Soft Roller Brush, directly from the official roborock store or authorized retailers.

For further assistance or support, please visit the official roborock websito o contattare il loro servizio clienti.