maXpeedingrods Coilovers Suspension Kit

1. Introduzione

This manual provides detailed instructions for the proper installation, adjustment, and maintenance of your maXpeedingrods Coilovers Suspension Kit, Model XP20YP, designed for the Mazda CX-4 (2016-2019). These coilovers are engineered to offer enhanced vehicle handling and adjustable ride height, allowing for a customized driving experience. Please read this manual thoroughly before beginning any installation or adjustment procedures.

The maXpeedingrods coilovers feature high-tensile springs, 6061 aluminum alloy components for durability, and preset damping values to maintain consistent handling characteristics.

2. Informazioni sulla sicurezza

• Installazione professionale consigliata: Installation of suspension components requires specialized tools and knowledge. It is highly recommended that installation be performed by a qualified professional.
• Supporto veicoli: Always ensure the vehicle is securely supported on jack stands or a lift before working underneath. Never rely solely on a jack.
• Dispositivi di protezione individuale: Wear appropriate safety gear, including eye protection, gloves, and sturdy footwear, during installation.
• Specifiche di coppia: Adhere strictly to the vehicle manufacturer's torque specifications for all fasteners. Improper torque can lead to component failure.
• Allineamento delle ruote: After installation, a professional wheel alignment is mandatory to ensure proper vehicle handling and tire wear.
• Prove su strada: Perform a cautious road test in a safe area after installation and adjustments to verify proper function and handling.

3. Contenuto della confezione

Verificare che tutti i componenti siano presenti e integri prima di iniziare l'installazione. Contattare immediatamente il fornitore in caso di componenti mancanti o danneggiati.

Descrizione dell'immagine: Un overhead view of the complete maXpeedingrods coilover suspension kit, including four fully assembled coilovers, separate rear springs, and two orange adjustment wrenches.

• Front Coilovers (2)
• Rear Coilovers (2)
• Adjustment Wrenches (2)
• Manuale di istruzioni (questo documento)

4. Guida all'installazione

This section outlines the general steps for installing the coilovers. Specific vehicle disassembly and reassembly procedures may vary. Refer to your vehicle's service manual for detailed instructions.

4.1. Controlli pre-installazione

• Ensure the vehicle is on a level surface and securely supported.
• Scollegare il terminale negativo della batteria del veicolo.
• Inspect all components for any shipping damage or manufacturing defects.

4.2. Removal of Original Suspension

1. Togliere le ruote.
2. Carefully disconnect any brake lines, ABS sensors, or sway bar links attached to the original strut assembly.
3. Unbolt the lower mounting points of the strut/shock absorber.
4. Access the upper mounting points (usually in the engine bay for front, or trunk/rear interior for rear) and unbolt them.
5. Carefully remove the entire original strut/shock assembly from the vehicle.

4.3. Installation of New Coilovers

Descrizione dell'immagine: A detailed diagram of a maXpeedingrods coilover, labeling its key components including the camber plate top mount, upper spring seat with radial bearing, full-length dust boot, high tensile spring, 6061-T6 aluminum perch, and heavy-duty lower mount.

1. Regolazione iniziale dell'altezza: Before installing, set the coilovers to a preliminary ride height. Refer to Section 5 for detailed adjustment procedures.
2. Install Upper Mount: Carefully position the new coilover assembly into the vehicle and secure the upper mounting bolts.
3. Install Lower Mount: Align the lower mounting points and secure them with the appropriate bolts.
4. Ricollegare i componenti: Reattach any brake lines, ABS sensors, and sway bar links that were disconnected. Ensure all lines and wires are clear of moving parts.
5. Repeat for all corners: Follow the same procedure for the remaining three wheels.
6. Coppia finale: Once all coilovers are installed, re-check and torque all fasteners to the vehicle manufacturer's specifications.

5. Installazione e regolazione

Your maXpeedingrods coilovers offer adjustable ride height and preset damping for optimal performance.

5.1. Ride Height Adjustment

The ride height can be adjusted by rotating the lower mount on the threaded shock body. This allows for a lowering range of 1-3 inches from the original ride height.

Descrizione dell'immagine: A diagram showing two coilovers side-by-side, one at a higher setting and one at a lower setting, illustrating the full-length height adjustment mechanism. Arrows indicate the upward and downward movement of the lower mount on the threaded shock body.

1. Loosen the locking ring located above the lower mount using the provided adjustment wrench.
2. Rotate the lower mount clockwise to lower the vehicle or counter-clockwise to raise it.
3. Once the desired height is achieved, tighten the locking ring securely against the lower mount.
4. Ensure both sides of an axle (front or rear) are adjusted to the same height to prevent uneven loading.

5.2. Laampregolazione

These coilovers come with a factory preset damping value. This setting is optimized to maintain consistent and predictable handling characteristics and reduce the risk of overloading the suspension system. No user adjustment for damping is required or possible with this model.

6. Considerazioni operative

• Periodo di rodaggio: Allow for a break-in period of approximately 500 miles after installation. During this time, avoid aggressive driving to allow the suspension components to settle.
• Allineamento delle ruote: A professional wheel alignment is crucial immediately after installation and any significant ride height adjustments. This ensures correct steering geometry and prevents premature tire wear.
• Stile di guida: While coilovers enhance performance, always drive responsibly and be aware of changes in vehicle dynamics, especially with a lowered ride height.

7. Manutenzione

• Ispezione regolare: Periodically inspect the coilovers for any signs of damage, leaks, or loose fasteners. Check for corrosion, especially on threaded sections.
• Pulizia: Keep the coilovers clean, especially the threaded sections, to prevent dirt and debris from hindering adjustments or causing wear. Use mild soap and water.
• Lubrificazione: Apply a thin layer of anti-seize lubricant to the threaded sections and locking rings during initial installation and periodically thereafter to ensure smooth height adjustments and prevent seizing.

8. Risoluzione Dei Problemi

• Rumori insoliti: If you hear clunking or squeaking noises, re-check all mounting bolts for proper torque. Inspect for any components rubbing or loose.
• Altezza di marcia irregolare: Ensure that the ride height is set equally on both sides of the vehicle (front and rear). A professional alignment can also help diagnose and correct unevenness.
• Maneggevolezza scadente: Verify that all components are installed correctly and securely. A professional wheel alignment is critical for optimal handling after suspension modifications.

9. Specifiche

10. Garanzia e supporto

maXpeedingrods products are manufactured to high standards. For specific warranty details, terms, and conditions, please refer to the warranty information provided with your purchase or visit the official maXpeedingrods website. For technical support or assistance, please contact maXpeedingrods customer service through their official channels.