Prodotto finitoview
The RadioMaster TX16S Mark II is an advanced open-source radio controller designed for remote control enthusiasts. It features upgraded V4.0 Hall Gimbals with 4 precision bearings for enhanced feel and centering. The redesigned plastics improve fit, finish, and durability. It offers an optimized power supply with reverse polarity protection and up to 2.2 amps of charging via its USB-C port. The 4.3-inch IPS color display provides intuitive programming with touch panel precision, and a DIY accessory socket is included for customization.
Componenti del prodotto
The RadioMaster TX16S MKII V4.0 package includes the following items:
- 1 * TX16S Mark II Radio Controller
- 1 * 18650 Tray (for battery installation)
- 1 * USB-C Cable (for charging and data transfer)
- 1 * Pellicola protettiva per lo schermo
- 1 pair of flat grips (for ergonomic customization)
Disposizione del trasmettitore
Istruzioni di installazione
1. Installazione della batteria
The TX16S MKII V4.0 supports 18650 batteries. Ensure correct polarity when inserting batteries into the provided tray. Connect the battery to the internal connector within the battery compartment.
2. Attacco cordino
For added security and comfort during operation, attach a lanyard to the designated loop on the transmitter.
3. Accensione iniziale e configurazione
Press and hold the power button to turn on the transmitter. The 4.3-inch IPS color display will show the operating system (EdgeTX or OpenTX). Follow on-screen prompts for initial setup, including throttle calibration if a "Throttle Warning" appears. The touch panel allows for intuitive navigation through menus.
Istruzioni per l'uso
The TX16S MKII V4.0 is a versatile remote control supporting both EdgeTX and OpenTX firmware, offering extensive customization and compatibility with various protocols (ELRS or 4in1 module versions). Familiarize yourself with the gimbals, switches, and trim buttons for precise control of your models.
Operazione generale finitaview
Regolazioni del giunto cardanico
The V4.0 Hall Gimbals are adjustable without disassembly. You can fine-tune the stick travel (minimum 38°, maximum 54°), horizontal axis tension, vertical axis tension, and gimbal mode (self-centering for throttle/elevator) to suit your preference. Refer to the labeled diagram for specific adjustment points.
Using EdgeTX Companion Software
The TX16S MKII V4.0 supports EdgeTX Companion PC software, allowing you to program all your model and radio settings from your computer. Connect the transmitter to your PC using the USB-C cable for firmware updates, model management, and configuration.
Manutenzione
- Pulizia: Utilizzare un panno morbido e asciutto per pulire l'esterno del trasmettitore. Evitare l'uso di prodotti chimici aggressivi o materiali abrasivi.
- Magazzinaggio: Conservare il trasmettitore in un luogo fresco e asciutto, lontano dalla luce solare diretta e da temperature estreme. Rimuovere le batterie se si prevede di non utilizzarlo per periodi prolungati.
- Aggiornamenti del firmware: Regularly check for and install the latest firmware updates for EdgeTX or OpenTX to ensure optimal performance and access to new features. Use the USB-C port and EdgeTX Companion software for updates.
- Cura della batteria: Follow the manufacturer's guidelines for charging and discharging your 18650 batteries to prolong their lifespan.
Risoluzione dei problemi
- "Throttle Warning" on startup: This indicates the throttle stick is not at its lowest position. Ensure the throttle stick is fully down before powering on or press any key to bypass the warning.
- Difficulty binding to receiver: Verify that the transmitter's internal module (ELRS or 4in1) is set to the correct protocol for your receiver. Ensure both the transmitter and receiver are in binding mode. Consult the receiver's manual for specific binding procedures.
- Problemi di visibilità dello schermo: Adjust the screen brightness in the system settings. For outdoor use, higher brightness settings may be required.
- General operational issues: Many issues can be resolved by ensuring the transmitter's firmware (EdgeTX/OpenTX) is up to date. Refer to the official RadioMaster website or EdgeTX/OpenTX documentation for detailed guides and community support.
Specifiche
| Caratteristica | Dettaglio |
|---|---|
| Dimensioni del prodotto | 8 x 6 x 4 pollici |
| Età consigliata dal produttore | 18 anni e oltre |
| Giunti cardanici | V4.0 Hall Gimbals with 4 precision bearings |
| Display | 4.3" IPS Color Display with touch panel |
| Ricarica | USB-C, up to 2.2 amps, reverse polarity protection |
| Supporto firmware | EdgeTX, OpenTX |
| Module Support | Internal ELRS or 4in1 (variant dependent), External JR module bay |
Informazioni sulla sicurezza
Please refer to the instruction manual before use. Always operate your remote control and models in a safe and responsible manner. Ensure all connections are secure and batteries are properly charged before each use. Keep the device away from water and extreme conditions.
Garanzia e supporto
For warranty information and technical support, please visit the official RadioMaster website or contact your retailer. Keep your proof of purchase for any warranty claims. Online resources and community forums for EdgeTX and OpenTX also provide valuable support and troubleshooting tips.
