THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
Guida rapida

Contenuto della confezione

Specifiche

Ripristino delle impostazioni di fabbrica

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

Scansiona il codice QR per view dettagli

https://bit.ly/488mkj9

Risoluzione dei problemi

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. Il dispositivo non si accende
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

Conformità alle normative FCC
Questo dispositivo è conforme alla parte 15 delle Norme FCC. Il funzionamento è soggetto alle due condizioni seguenti: (1) Questo dispositivo non può causare interferenze dannose e (2) questo dispositivo deve accettare qualsiasi interferenza ricevuta, comprese le interferenze che possono causare un funzionamento indesiderato.
Eventuali cambiamenti o modifiche non espressamente approvati dalla parte responsabile della conformità potrebbero invalidare il diritto dell'utente a utilizzare l'apparecchiatura.
Nota: Questa apparecchiatura è stata testata e ritenuta conforme ai limiti previsti per i dispositivi digitali di Classe B, ai sensi della parte 15 delle norme FCC.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Riorientare o riposizionare l’antenna ricevente.
– Aumentare la separazione tra l’apparecchiatura e il ricevitore.
– Collegare l’apparecchiatura a una presa di corrente di un circuito diverso da quello a cui è collegato il ricevitore.
– Per assistenza, consultare il rivenditore o un tecnico radio/TV esperto.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

Per la garanzia limitata, visitare
https://thirdreality.com/faq-help-center/
Per l'assistenza clienti, contattaci all'indirizzo
info@3reality.com o visita www.thirdreality.com
Per domande su altre piattaforme, visitare il corrispondente
platform’s application/support platform.