Manuale utente del misuratore d'angolo serie UNI-T LM320D

Dopo aver letto il presente manuale, si consiglia di conservarlo in un luogo facilmente accessibile, preferibilmente vicino al dispositivo, per poterlo consultare in futuro.

GARANZIA LIMITATA E RESPONSABILITÀ

Uni-Trend guarantees that the product is free from any defect in material and workmanship within one year from the purchase date. This warranty does not apply to damages caused by accident, negligence,misuse,modification,contamination and improper handling. The dealer shall not be entitled to give any other warranty on behalf of Uni-Trend. If you need warranty service within the warranty period, please contact authorized service center or send the product back with problem description.This warranty is the only compensation you can obtain.Uni-Trend will not be responsible for any special,indirect, incidental or subsequent damage or loss caused by any reason or speculation. As some areas or countries do not allow imitations on implied warranties and incidental or subsequent damage, the above limitation of liability and stipulation may not apply to you.

Struttura del prodotto

Operazioni

Power On: In power-off state, long press pulsante per accendere
Power Off: In power-on state, long press pulsante per spegnere.

Laser ON/OFF (LM320E)

In stato di accensione, premere brevemente button to make all lasers on, and short press button again to make the laser off on the right side. Short press button again, the laser on the left side is off, and then short press button again to make all lasers off.

Laser ON/OFF (LM320F)

In stato di accensione, premere brevemente button to make all lasers on. and short press button again to make the laser off on the top side. Short press button again, the laser on the left side is off, and then short press button again to make the laser off on the right side; Short press button again to make all lasers off.

Misurazione dell'angolo

In power- on state, place the device on the inclined plane, the show value on the screen is the angle value between the inclined plane and the horizontal plane.

REF (Modalità Valore Relativo):

Nella modalità di misurazione, premere brevemente button to enter the Relative Value mode (Set the current value to 0), and short press it again to exit the mode.

Modalità di calibrazione

Place the device on the absolute horizon, continuously long press button for three times to enter the self – calibration mode (see figure 1); CALO flashes on the screen, short press button to confirm to enter the auto zero calibration (see figure 2).

Ruotare il dispositivo di 90 gradi, premere button and CAL1 flashes on the screen; short press button to confirm to enter the auto zero calibration (see figure 3). Rotate the device 90 degrees, press button and CAL2 flashes on the screen; short press button to confirm to enter the auto zero calibration (see figure 4). Rotate the device 90 degrees, press button and CAL3 flashes on the screen; short press button to confirm to enter the auto zero calibration (see figure 5). The the calibration, and recover the use of is after power-on.

Blocco dati

Nella modalità di misurazione, premere brevemente button to lock the current measured data; short press again to unlock the data.

Interruttore unità e suono ON/OFF

For LM320E/LM320F, long press button to switch the unit (in ° unit by default), mm/m,%, or in/ft. In in/ft unit display, when ‘-‘icon shows on the screen, the range of measured value is within ‘measured value -1/8 ~ measured value’;when+’icon shows, the range of measured value is within’measured value ~ measured value+1/8′. For example, 11.7/8 display means 11 and 7/8; 9-3/8 display means 9 and 3/8.

For LM320D, short press UNIT button to switch the unit.

For LM320E/LM320F, short press button to make the sound indication on/off; For LM320D, short press button to make the sound indication on/off.

Carica

Quando l'icona della batteria è scarica shows on the screen, please charge the device with charging cable in the accessories. In the power-off state, battery is fully charged when its icon stops flashing and not showed on the screen any more.

Parametri tecnici

Attenzione:

Do not use organic solvents to wash the percision equipmet. Take it far away from water and corrosives.
Do not damage the surface of device; use soft cloth to wipe the dust for its accuracy.

For power saving, the device will be auto power off if no operations in 5 minutes.

RADIAZIONE LASER
NON FISSARE NEL FASCIO
PRODOTTO LASER DI CONSUMO DI CLASSE 2
Compliance with lEC/EN 60825-1, EN 50689.

The manual is subject to changge without prior notice!

Due to different batches, the materials and details of actual products may be slightly different from the graphic information, please refer to the actual product received. Experimental data provided in the page is from internal laboratory of UNI-T, but it should not be a reference for customer to place orders. Any questions, please contact thecustomer service, thanks!

TECNOLOGIA UNI-TREND (CHINA) CO., LTD.

No.6, Gong Ye Bei 1a strada,
Industriale high-tech nazionale del lago Songshan
Zona di sviluppo, città di Dongguan,
Provincia del Guangdong, Cina
Tel: (86-769) 8572 3888
www.uni-trend.com
P/N: 110401113327X

Documenti / Risorse

Misuratore d'angolo serie UNI-T LM320D [pdf] Manuale d'uso
Misuratore d'angolo serie LM320D, LM320E, LM320F, LM320D, Serie LM320D, Misuratore d'angolo, Misuratore

Riferimenti

Manuale d'uso